How to wash the mesh from the hood. How to clean grease from a kitchen hood. Using special care products for hoods, microwaves, and ovens

A kitchen hood often contains a large amount of old and well-dried grease, so the question of how to clean the hood in the kitchen is asked by most housewives. Many people recommend washing the hood immediately after cooking and not waiting until it is very clogged. Since in in this case You will have to make much more effort and spend a lot of time to do this.

It is worth noting that the hood is an important item kitchen furniture, which allows burning and smoke to escape through the ventilation system. Combustion objects passing through it clog the hood filter with unburnt fat and many other pollutants.

In order not to disturb normal functioning hood installed above gas stove, cleaning work should be carried out regularly.

In order to figure out how to clean a kitchen hood, you should understand the sequence of actions. All the basic recommendations that allow you to independently remove traces of grease from all surfaces of the hood are given in the corresponding instructions for this product.

There will be a diagram of the assembly and disassembly of the structure, since the main measures regarding the removal of old fat at home will be carried out precisely inside this device.

• To clean the mesh in the hood, you must first protect yourself by disconnecting the structure from the power supply. Otherwise, it is strictly forbidden to disassemble it, especially if you do not touch the motor or try to wet clean it.
• Directly on the hood itself there should be a diagram on how to remove the grille from the hood. It is usually held in place by snap-off clips. Carbon filter in the hood it is usually hidden behind this grille. As a rule, this is where the bulk of contaminants accumulate. In order not to think about how to quickly clean it from dirt, such a filter can simply be replaced - such products are not too expensive.
• When cleaning the kitchen hood from dirt, you should remember that it is connected to the ventilation vent using a profile, round or corrugated pipe. It also accumulates a certain amount of soot and grease during direct use. Easiest to wash profile pipe, if it is not too long. A longer structure should be round in cross-section - this will not only make it easier to clean, but also slow down the accumulation of fat.
• Clear filter kitchen hood Fat is not that difficult to remove, but it will have to be removed. This is not too difficult to do, and if you know certain tricks, then the cleaning process itself will be quite simple and will take a minimum amount of free time.
• Usually no one removes the body of the structure; it is washed both outside and inside.
• At the last stage, you should assemble the hood above the stove and connect it to the electrical network.

There are special hoods on sale that have turboair type filters installed - their design does not mean that these elements can be cleaned; you will have to install new products instead. To find out whether it is permissible to clean the hood from grease at home, you should carefully read the instructions.

It is worth saying that in any case there should be a sufficient amount of cleaning products on hand. If we take into account certain nuances and subtlety, then getting rid of fat on a household kitchen hood will not be too problematic.

To clean the hood grate from grease, you should use special powders that should not contain abrasive materials, otherwise the surfaces will be scratched and lose their attractive appearance. Another disadvantage of using such products is the appearance of an additional relief on the surface, in which additional fat will accumulate, and in the future it will be very difficult to clean it out.

There are a lot of options for getting rid of grease from the hood in the kitchen or bathroom. If you can’t choose a cleaning agent for the walls and hoods in the kitchen yourself, then you can go to a specialized store household chemicals And consult with specialists.

1. If the hood is made of stainless steel, then it can be removed from fat accumulation with ordinary baking soda. It is dissolved in a small amount of water and this solution is passed over contaminated surfaces.
2. Quite a large number of alkaline elements, capable of breaking down fat even in turboair type hoods, are contained in the most ordinary laundry soap.
3. The hood can be properly cleaned of grease at home using ordinary means for dish washing. The stronger their effect, the more likely it is that you will soon have to resort to using them again.
4. The hood in the kitchen will be thoroughly cleaned of grease. professional products aimed at removing contaminants from the surface of gas stoves.

It is worth noting that the choice of products for turboair hoods will be much narrower; in addition, these products are not intended for cleaning at all. Reliable products that allow you to clean the hood mesh from grease will not be relatively cheap, so you should immediately prepare for the fact that you will have to pay quite a lot for them. a large amount money.

Regarding how to clean the filter, there are a number of quite simple tips. You can remove all kinds of dirt from the surface of these small gratings using in various ways. In particular, you can use charcoal cleansers.

These products also contain a large amount of alkaline substances that will dissolve body fat and clean the grate. If desired, they can even treat the fan motor and the fan itself. If the latter can be removed from fatty deposits, it will be much more effective at removing combustion products and unpleasant odors, leaving only fresh air in the kitchen.

Many not very experienced housewives are wondering how to clean the hood from grease if it has not yet become too dirty. First of all, in this case it is necessary to determine the degree of contamination.

Mild degree

A light degree is indicated by light droplets of fat that have not yet had time to harden, so in this case it will be much easier to clean the mesh from the hood.

There won’t be any particular difficulties with filters here either. The technique regarding how to clean the grate includes several actions.

• Take a container of suitable capacity and fill it fairly hot water with addition baking soda or other cleaning product. Filters are immersed there, trying to ensure that they are completely under water.
• The container is left for about an hour or two so that the filter can be cleaned there on its own without unnecessary physical impact.
• When the grease is removed from the surface of the filters, the remaining water and detergent should be washed off. This is first done using warm water, gradually lowering its temperature. This procedure must be carried out quite efficiently so that there is not the slightest trace detergent no residue left on the surface of the filter or the hood itself. Ultimately, this can have a very negative impact on the operation of the entire structure.

Severe degree

If the fat has become dark Brown color, this means that it had time to freeze quite strongly. In this case, you should use a folk remedy such as digestion.

Pour water into the container so that all the components of the hood are under it, put it on the fire and chop about half a piece of fairly cheap laundry soap. Two tablespoons are poured into the same container. baking soda. The water is brought to a boil and boiled for about half an hour. If necessary, you will need to add water if it suddenly evaporates and some elements of the hood appear above its surface.

If the hood is cleaned correctly, it will work reliably. To maintain a clean condition, major cleaning will have to be carried out no more than once every six months.

A kitchen hood, taking the brunt of the fight against grease and soot, helps us maintain cleanliness and a fresh aroma. But at the same time, fatty fumes settling inside and on the surface can impede its flawless operation. And for housewives to add more hassle when cleaning household appliances. To paraphrase a well-known saying: if you love to cook, you also love to wash the hood.

Time to wash the hood

Maintaining cleanliness in the kitchen is a process the frequency of which each housewife chooses herself. Some people wash everything inside and out every day, while others limit themselves to everyday washing of dishes, and general cleaning held once a quarter.

Indeed, not all things in the kitchen require daily cleaning, and the hood is one of them. However, you need to understand when it’s time to wash the hood and with what regularity it should be done, so that you don’t waste a lot of time and effort cleaning old dirt:

• if you cook quite often using a hood, then the filter should be cleaned at least once every two weeks;
• If the intensity of cooking is not very high, then cleaning once a month is enough.

If traces of dirt are visible from outside exhaust surface, filter covered with grease ahead of schedule, and odors are poorly removed from the kitchen, then it’s time to start cleaning without waiting for the allotted time.

Not everything in the kitchen requires daily cleaning

But in any case, do not forget to do general cleaning of the hood at least once a quarter, washing all its components.

What you need to know before you start cleaning

Depending on the design and method of fastening, there are different following types hoods:

• built-in - built into Kitchen Cabinet, takes up little space and fits harmoniously into the space. Externally it gets less dirty, because it is hidden in a closet;
• suspended (horizontal and vertical) - the most affordable option in terms of price, characterized by simplicity of design and mounting to a wall or ceiling;
• insular - found in large kitchen areas, when the area allows you to place hob a table in the middle of the room and install a hood above it;
• dome (fireplace) - a common type of hood that looks like a roof canopy with a pipe. The most difficult thing to maintain is that dust and dirt settle on both the visor and the air duct pipe.

Photo gallery: types of kitchen hoods

Built-in hood - beautiful and practical Hanging hood - budget and affordable Island hood - chic and scope Dome hood - traditional and functional

Depending on the operating mode, there are:

• recirculating hoods - provide air purification through a filtration system. Both reusable and disposable filters can be used and must be replaced periodically;
• flow-through - they clean the air and remove it outside using an air duct. Unlike recirculation ones, they eliminate odors better, but are more difficult to maintain, since they require periodic cleaning of not only the filters, but also the air duct.

Built-in and suspended hoods, as a rule, have a recirculation mode. The main difference is that wall-mounted ones have reusable budget filters, while built-in ones are most often equipped with disposable carbon filters.

Island and dome units can operate in both flow-through ventilation and recirculation modes. But to use the first mode, it is necessary to construct an air duct.

Step-by-step cleaning instructions

First of all, you need to read the instructions, studying the design of the hood, the rules for disassembly and assembly.

Regardless of the type of hood, the process of preparing for regular filter cleaning includes the following steps:

For general cleaning, you will need to additionally disassemble the hood as much as possible:

1. The first three points are similar to those indicated for regular filter cleaning.
2. If the configuration of the hood provides for the presence of an air duct pipe and it can be disassembled, then the pipe is removed - it also needs to be cleaned.
3. For ease of disassembly, it is better to remove the hood from its mounts to the cabinet, wall or ceiling.
4. Remove the protective cover of the hood (if equipped) by unscrewing the bolts to get to the internal elements of the device.
5. Remove the fan cover depending on the mounting method.
6. At least once a year it is necessary to get to the engine - it also needs preventive maintenance.
7. Reassemble the parts after they have been cleaned and dried.

Photo gallery: disassembling a kitchen hood for general cleaning (steps 2–6)

If the air duct is not removable, then over time it is better to replace it Before you start major cleaning, you need to disconnect all parts of the hood When unscrewing the bolts, fold them carefully so as not to lose them The motor is hidden behind the fan cover There are connecting wires near the motor - you need to be careful not to damage anything

Video: cleaning the hood with complete disassembly

Features of washing different materials

Main components of the hood:

• top cover or cap,
• air duct,
• fan,
• grease filters,
• motor,
• frame.

A large amount of grease and dirt settles on the top of the hood, so the surface is treated with one of the means for removing grease from the stove and cleaned with a sponge. To avoid streaks, the clean surface must be wiped dry. Stainless steel needs to be wiped lengthwise to avoid streaks.

The duct is a corrugated tube, which is usually made of aluminum, stainless steel or plastic. Plastic is easier to clean, because less dirt sticks to such a surface, and grease does not accumulate in the recesses. To clean the air duct, it is necessary to rinse it with water, after soaking it in a solution using a degreaser.

Degreasers are suitable for cleaning the air duct

Dirt particles also accumulate on the fan cover, so it needs to be removed and washed, and if necessary, soaked in soapy water.

The hood body also needs processing. Small stains can be removed using dishwashing detergent, then rinsed off warm water and wipe dry.

The motor is the heart of the hood, so it must be cleaned at least once a year. It is better to have a specialist do this, but you can do it yourself. You need to unscrew all removable parts and wipe them with a cloth moistened with alcohol. Next, lubricate the inner bearing with machine oil.

The main defender in the fight against grease and soot is the filter. It takes on the bulk of the pollution. But cleaning it is not so difficult if you know a few tricks and tricks.

Important! Not all filters can be cleaned - you can find the relevant information in the instructions for the hood.

IN modern hoods The following types of these accessories are used:

The easiest way to clean the mesh and grate is to immerse the filter in a container and fill it with hot salted water, leaving for half an hour. Another option is to apply a grease-dissolving detergent and use a brush to clean the grates and mesh. However, these methods are effective in case of minor contamination and are more suitable for regular use.

Video: three ways to clean the hood mesh

When all parts are cleaned, they must be thoroughly rinsed and dried.

Methods for removing dirt and grease

At the hardware store you can find products for removing grease and soot in any price category.

Chemical compositions

The most effective of them are Cinderella “Anti-grease” and Synergetic cleaner, which can be used on any surface, since they do not contain aggressive chemicals.

Also universal means To remove greasy stains from any surfaces, Domestos spray, Economy-Santry and Cif kitchen cleaner are available, but they are too old stains They may not remove grease and soot.

Cilit Bang Anti-grease spray is used for cleaning plastic, glass, ceramic and enamel surfaces. The similar Mister Muscle Kitchen Spray is slightly less effective and cannot be used on painted, aluminum, lacquered or wooden items.

The application process for all of these products is similar: they are applied to the contaminated surface, then washed off with water. The only difference is the exposure time: from 5 to 20 minutes, depending on the effectiveness. Like any household chemicals, they require the use of gloves to protect the skin of your hands.

Folk recipes

If you decide to wash the hood for the first time in long term service of the device, and the ingrained fat does not want to give in, then you can use the following recipes:

Video: comparison of two cleaning products

Prohibited tricks

Do not forget that you cannot clean the hood while it is plugged into the mains. This is primarily dangerous for you, but the device may also fail.

Read the instructions carefully: if the manufacturer has not stated that the hood parts can be washed in the dishwasher, then it is better not to do so.

It is important to know what material the hood parts are made of. Aggressive chemicals can damage aluminum, as a result the grille and mesh will oxidize and darken.

Adhered grease and dirt can be removed with a scraper, but you should use a plastic one for this purpose, as a metal one can damage glossy finish or enamel surfaces. For the same reason, metal brushes and abrasive sponges should not be used.

To clean the hood, use a scraper with a rubber or plastic attachment.

To extend the life of household appliances, they need systematic care. You need to know how to clean grease from your kitchen hood. Fat is the main enemy kitchen surfaces. It settles on the stove, on the tiles, on the facades of furniture. The grease trap of the hood takes the brunt of it. This affects the appearance and deteriorates functionality.

All parts that come into contact with grease and dust need to be cleaned. Be sure to read the instructions for use. You need to pay attention to which parts are removable and with what means they can be treated. Without this knowledge, you can irreversibly damage the device. After all the manipulations, the main function should be restored - trapping fat and purifying the air.

Preparatory stage

Using the instructions, we disassemble the hood. We remove all elements that have a greasy coating and can be dismantled. If the parts are screwed on, remove the bolts and put everything together so that they do not interfere or get lost.

We outline a rough plan of action. Adjust it depending on the type of kitchen hood you have.

1. 1 Unplug the power cord from the outlet.
2. 2 Remove the grease filters. If they are disposable, prepare a replacement one.
3. 3 If the design allows, remove the air duct. Otherwise, we clean the accessible part.
4. 4 Clean soot from external and internal surfaces.
5. 5 Clean the grille.
6. 6 Replace disposable filters (if your model has them).
7. 7 Dry the washed parts and assemble the kitchen hood.
8. 8 Connect the cord to the electrical outlet.

We figured out the action plan. Now let's figure out how to clean the hood in the kitchen at home.

Steam cleaning

Most effective method Wash the kitchen hood filter from grease, wash its external and internal fragments - steam cleaning. A steam generator is a unit that allows, without the use of chemicals Clean almost any surface. Another advantage of this miracle machine is that the steam disinfects the surface, because its temperature is above 150°C. Steam allows you to wash off grease from your hood in a matter of minutes without special effort.

Many people believe that a steam generator costs a lot of money and not everyone can afford it. This is a misconception. All kinds of attachments make it universal assistant not just in the kitchen. The bathtub, toilet and washbasins will be cleaned and disinfected. Steam does not cause allergies. The financial benefit can be seen by comparing the cost of the unit and the annual cost of the products you use for cleaning. We get clear example how long it will take to recoup this investment.

Automatic cleansing and folk remedies

IN modern world ideal option cleaning is considered to be one that does not require the expenditure of effort and time. Dishwasher - great way clean the grate without bothering. This option is suitable if the kitchen hood is made of stainless steel or the parts are covered with enamel.

We put all the parts that need cleaning in the dishwasher, fill it with detergent and turn it on. We spend the freed time on completing the next point.

The question arises, how to wash the kitchen hood filter for those who do not have the above equipment. The methods are varied. Using improvised means that any housewife has in her kitchen, you can clean the hood of grease. Yes, it won’t be quick and will require effort, but it will save you money.

Let's get acquainted with all the valuable products that help solve many everyday problems effectively and on a budget.

Baking soda and vinegar in the fight against pollution

Baking soda is an excellent cleaning agent. But it requires a container, preferably a large one. Boiling is best. If not, choose the largest pan, pour water into it and put it on the fire. Throw 200-250 g of soda into boiling water and stir until completely dissolved. If the dimensions allow, lower the entire hood grate into the liquid and boil for about 30 minutes, depending on the degree of contamination. If the dimensions do not allow processing the whole, we immerse one side, and after a while we add more soda and turn the mesh over to the other side. You can lower the corners of the grille. Then turn it over 4 times and add baking soda after each.

Grease, dust and soot will come off on their own. This will cause the solution to turn yellow. We take out the hood grate and wash it under running water and polish with a sponge.

Vinegar is not only a seasoning and a liquid for preserving food. Like any acid, undiluted acetic acid has an aggressive effect on fats. It also corrodes the skin of the hands and burns the nasal mucosa when inhaled. Therefore, you need to work with gloves and a respirator.

Apply vinegar to the removable panels and leave for 15-20 minutes. The dirt will dissolve and all you need to do is remove the remaining fragments with a sponge, rinse with water and dry.

It is worth remembering one more acid - citric acid. Natural lemon will also work. It is cut into halves and rubbed onto surfaces that require cleaning. Using citric acid act in the same way as in the previous example with acetic acid. We wait a few minutes and clean the parts of the hood from grease. If the stains are complex, be prepared to repeat the procedure several times.

Using laundry soap and ammonia

There are several options for cleaning grease from hoods using soap.

1. 1 You can rub the block in warm water, dissolve it and immerse the parts in this mixture.
2. 2 Alternatively, rub the grate itself with soap. Pour hot water into a baking tray, place greased grease in it and place in a hot oven. Boil there for about half an hour. When dissolved, laundry soap breaks down even old fat. After soaking, the filters are removed and washed thoroughly.

Ammonia - tested and a win-win. The presence of a pungent and unpleasant odor forces one to resort to protective measures. The room must be well ventilated, and the respiratory system must be protected with a respirator.

Pour half a glass of alcohol into 3.5 liters of warm water. Lower the grease trap for 4 hours. When the dirt has dissolved, remove it with a sponge and rinse. This method is suitable for heavily soiled surfaces.

Household chemicals

In order not to greatly complicate the process of preparing cleaning mixtures, you can use ready-made chemical compositions, such as:

• dishwashing liquid;
• "White";
• facilities different manufacturers based on formic acid;
• powders or liquids for cleaning pipes.

To remove grease, you can use folk remedies. The procedure is the same as when using conventional means:

1. 1 Apply to the surface (dip the part into the solution).
2. 2 Wait for time.
3. 3 Rub with a washcloth or brush.
4. 4 Rinse with water.
5. 5 Dry.

Cleaning the outer casing

When internal filters cleaned and dry, move on to the front part. The cleanliness of the outside of the hood greatly affects the overall neatness of the kitchen. The treachery of this detail is that dust settles on the fat and “cements” it. Exactly because of this reason outer part It's better to wash regularly. The use of abrasive powders or iron scrapers is not permitted on this surface. They may leave scratches or remove the glossy finish. More liquid products are also excluded because they can get on the face, neck or hands.

A few simple recommendations will help you easily cope with this mission:

1. 1 Take dishwashing detergent, apply it to a damp sponge and rub the surface. Leave for half an hour and wash with a damp cloth. If there are hard grease spots left and do not want to be washed off, you can rub them with a rubber scraper (as for car windows).
2. 2 It’s easier to clean a kitchen hood if you don’t turn it on gas burner idle. Dry heat forms a deposit of fat on the surface, and it is more firmly fixed.
3. 3 If there are buttons on the hood and flooding occurs, then remove the mechanical control unit for cleaning. It is advisable to ask someone who has experience in this matter, otherwise the cleaning will end in failure.

How often should you clean?

How to wash off fat and how often should such cleaning be carried out? Each person answers this question individually. It all depends on the hostess’s availability of free time, on the family’s eating style, and finally, on her temperament. There are women who cannot sleep if the kitchen does not shine.

If the family is large and you have to cook often, if household members prefer fried food rather than steamed food, the deadline quality work collection filters is reduced. On average, general cleaning can be done once every quarter or six months. The filter may need to be cleaned every month. In this case, the external structure can be washed once a week or more often. It all depends on desire.

Modern hoods are equipped with replaceable disposable filters.

They need to be replaced when they become dirty. It would be a good idea to purchase several additional filters when purchasing a hood. This will insure against unnecessary expenses if the manufacturer decides to stop producing equipment of this type.

Systematically washing the grill in the dishwasher is a great option that will save time and effort, and the results will be unsurpassed.

Care and timely care will extend the “life” of your kitchen assistant.

Almost every kitchen has such convenient appliances as exhaust system, which tends to get dirty and accumulate drops of fat on the walls and grill. This irritates all housewives, since such contaminants, especially old ones, are very difficult to remove.

What to do before washing the hood

It is impossible to wash equipment efficiently, without certain knowledge and skills, at home. The most an inexperienced housewife can think of is to wipe the walls and grill with a rag, but such a procedure will not remove grease. First you need to understand how the structure is disassembled, because in assembled form
There is no way to clean it properly.

1. Before disassembling the device, be sure to disconnect it from the power supply system to avoid electric shock.
2. The equipment itself should have a sticker with detailed instructions, which includes a diagram for disassembling the structure. Usually there are latches on the sides; you need to snap them off and remove the top cover.
3. When cleaning equipment from grease, you should know that the hollow pipe that connects the hood with ventilation also needs to be washed, because greasy deposits accumulate in large quantities there too. Some craftsmen somehow got into the habit of changing the corrugation once every month or two, thereby freeing themselves from tedious washing. But not every technique will work with such a trick, since you need to be able to do everything correctly, otherwise you can break some part and add to your problems.
4. Then you should remove the air filter. This is not difficult at all, you also need to wash it.
5. The hood body itself is not removable; just wipe it with a sponge and move on to washing the remaining parts.

IMPORTANT! Carefully read the instructions for your hood, as some models have turboair parts, that is, they cannot be washed, they must be replaced.

In addition to cleaning the internal parts, you need to thoroughly wash the outer body of the equipment. The non-built-in design especially needs to be washed, since the main part of such a hood is not hidden in kitchen set, but is located directly above the gas stove and collects all the soot and fat on itself.
All this sticky substance settles on the walls of the case and, although it is not difficult to wash it, it is quite inconvenient, since you will have to wash it while standing on a chair and reaching up. detailed instructions for washing the body:

1. Moisten the surface with warm water.
2. Apply a tablespoon of dishwashing gel to a hard sponge and apply to the body of the structure, making sure that the liquid does not drip onto the stove and floor.
3. Rub the surface with a hard and dense sponge or brush and leave for 20–30 minutes.
4. For persistent stains, lemon juice, a product with abrasive particles, like soda, or a strongly foaming detergent will help. kitchen utensils and technology.
5. After cleaning chemical composition Rinse everything thoroughly with water and dry with a cloth.
6. Wipe the washed surface with a soft, dry cloth to remove all stains and give the hood a shine.

IMPORTANT! Very old greasy crusts on the body can be removed using a plastic scraper; a metal scraper cannot be used - it will damage and scratch protective covering hood box.

How to clean the grille from the hood

The grille is one of the components of the design; thanks to its mesh structure, it does an excellent job of cleaning the air in the room from grease particles and protects the internal parts and mechanism of the unit from oil deposits. Taking all the dirt on itself, it becomes yellow, sticky and smoky in appearance - it is difficult to wash this structural element. With some effort, the filter can be washed with a chemical or mechanical cleaning. In addition to expensive compounds, you can use laundry soap; it will perfectly corrode grease deposits if you soak the grate in a soapy solution and then scrub off the remaining dirt with a brush.

IMPORTANT! To clean the filter using a soap solution, you need to choose 72% soap - it is easily rubbed on a coarse grater. After an hour of soaking in this water, all the dirt will come off without difficulty, and the filter will shine again.

Treatment with soda solution

Almost all manufacturing companies exhaust equipment, it is advised to wash both the front panels and the internal parts and filter only with a mild soap solution or water diluted with dishwashing gel. However, this method does not work in all cases; it can be improved by adding baking soda to the composition.
Master Class:

1. Pour hot water into a bucket, either from a kettle or from a tap.
2. Pour a quarter cup of baking soda and a spoonful of dish soap into a bucket of water.
3. Stir the mixture thoroughly with a handy tool, but not with your hand, until a rich foam forms.
4. Place the cleaning filter in a container and leave to soak for 15 minutes.
5. Rub the product with a hard sponge or brush and rinse in the bathroom under the shower.
6. Wipe dry with a cloth and put back in the hood.

The outer surface of the hood can also be soaked with this composition and left for a few minutes, then rubbed with a brush and rinsed with warm water.

IMPORTANT! This method helps to clean the hood parts almost always, but especially advanced cases you need to boil the filter in a soap-soda mixture for about 7-10 minutes, then the effect will be much better.

Using ammonia

If the soda method did not help, and contaminants remain on the filter and other parts of the kitchen appliance, then you can try to clean them with ammonia. For the composition you need to mix in 4 liters hot water half a tablespoon of alcohol. When working with the composition, you must wear a mask on your face, as the smell will be sharp and pungent, and you can also burn your mucous membranes or open a window or window. You will have to soak the grate for about 2 hours, then clean it with a sponge and rinse it in the shower. Leave to dry or wipe away moisture with a rag or paper towel.

How to clean grease from a hood with soapy water

To make the solution, you need to dissolve half a bar of 72% laundry soap in 3 liters of hot water. Small parts of the hood should be boiled in a soap mixture, and the grate should be soaked and mechanically treated with a scraper. Soap solution slowly breaks down fat and oil, and the remaining dirt after soaking can be removed with a plastic scraper or a stiff brush.

Treatment with acetic or citric acid

To treat parts of the unit you need to take 9% table vinegar and rub all the parts with it. The grate can be soaked in the vinegar solution for 15 minutes.

IMPORTANT! When cleaning in this way, be sure to wear gloves and with the window open.

To peel with lemon, you need to remove the peel from the lemon and cut it into two parts. Wipe all the extraction mechanisms and the outer box with the pulp, let the juice absorb for 10–15 minutes. Afterwards, simply rinse with water and wipe with a napkin.

IMPORTANT! If the grate is heavily contaminated with sticky residue, then you need to soak it in a solution of citric acid overnight.

How to Clean a Hood Grille Using Drain Cleaner

This method is used when you need to remove very old pollution, which have been accumulating for years. You can soak the grate and other small parts of the hood in the liquid solution for 25 minutes and rinse under hot water. If it is a powder, then you need to dilute it in water and then carry out the procedure for processing the gadget.

How to clean grease from a kitchen hood filter

To clean this part of the hood, you can use a variety of products. Compositions based on charcoal are effective. They contain many alkaline components that quickly deal with fat and oil. The method for cleaning an element depends entirely on the degree of contamination:

1. Easy degree. These are small droplets of pretty fat light color, they have not yet hardened and are easy to remove. In this case, the grate is soaked for 3-3 hours in soapy or soda solution. Then clean off any remaining dirt with a brush. Wash the filter under hot water using detergent, gradually lowering the temperature. The main thing is that there are no detergents or chemicals left on the filter, otherwise the mechanism may fail.
2. Hard to erase. A situation in which dark brown and red fat is on the hood parts. Most effective method- this is digestion. Place all the parts in a container with water, add pieces of grated laundry soap and 3 tablespoons of baking soda and boil for 30 minutes.

A well-cleaned hood will please the eyes of the owners and work more productively. Major cleaning is usually done every six months.

Where food is prepared there should be perfect cleanliness. This applies not only to dishes and stoves, but also to the hood in the kitchen. This useful device helps get rid of unpleasant odor tobacco smoke and burning in the kitchen and throughout the apartment, which often accompany the cooking process. With these advantages, the hood tends to quickly become dirty and covered with plaque and greasy stains, so it is better to regularly clean the hood grille, body and motor from carbon deposits, soot and grease.

This must be done because large quantities contamination, the grill becomes clogged, the functionality of the device is significantly reduced, and unpleasant odors spread throughout the apartment.

The hood must be washed regularly, since the filtered air carries soot, dust and droplets of fat that settle on the grille.

How to clean a kitchen hood

The hood should be cleaned following certain rules and sequence of actions. The work is performed in this order:

• Disconnect the device from the network.
• Remove the filters (if they are disposable, make sure you have spare ones).
• Remove the air duct if required by design features. If it is impossible to disconnect it, limit yourself to cleaning the accessible part of the device.
• Wash the hood filter from grease or, if you have disposable filters, replace them with new ones.
• Clean the fan.
• Clean the filter grid.
• Wait until the washed parts dry completely.
• Reinstall all parts.
• Connect the hood to the network.

Remember to be careful when cleaning your hood and always unplug the appliance.

Cleaning the hood with detergents

You can find it in supermarkets great amount household chemicals that can remove even old dirt and are ideal for cleaning kitchen hoods.

When there is a lot of dirt and the hood parts have not been cleaned long time, improvised means may be ineffective. In such cases, it is impossible to do without the use of aggressive means.

The grease remover is applied as described in the instructions and distributed evenly over the surface of the grate. After some time has passed, usually 5-15 minutes, cleaning is carried out and the chemical is washed off big amount water using a sponge or cloth.

If you use strong chemicals, protect your respiratory system with a mask and your hands with rubber gloves. Open the windows to prevent the smell from spreading throughout the apartment, and only then start working.

• To avoid damaging the hood parts, test the selected product on a small area. If the chemical does not harm the surface, you can begin cleaning the entire part. Apply the product to the surface of the grate and leave for 5-7 minutes.
• After the aggressive substances have taken effect, clean the parts first with a brush and then wipe with a sponge. At the end of the work, you need to thoroughly wash off any remaining grease and chemical cleaner from the surfaces and dry the parts.

However, not every family can afford the purchase of an expensive product; moreover, some substances included in gels, sprays and powders are very toxic and can cause allergies. If for one reason or another you do not plan to purchase a chemical cleaning product, use folk recipes getting rid of fat.

How to clean the hood grille using folk remedies

In order to remove soot and greasy deposits from the grill at home, simple and inexpensive products that every housewife can find are suitable.

Laundry soap or dishwashing detergent

• Any of these products is dissolved in water, maintaining a ratio of 1:4.
• The hood parts are soaked in the resulting solution for 1-2 hours, after which they are doused with boiling water and washed with a sponge.
• You can reinstall the parts only after they are completely dry.

Baking soda

You can boil the dirty mesh and filters in a baking soda solution.

• Fill in large capacity with water 1 glass of soda and put on fire.
• After the powder has dissolved, place the hood parts there and boil for 30 minutes.
• After this, all you have to do is rinse the grille under water.
• If slight dirt If any remain, remove them with a foam sponge.

Ammonia

This product will help wash away even the strongest and oldest stains, but if you decide to use this method, take care of respiratory protection by wearing a respirator. Open the windows in the room so that the acrid smell of ammonia does not spread throughout the apartment.

Salt

Add 1 cup to a large pot of water table salt and wait for complete dissolution. Reheat salt water, but do not bring to a boil, and place the grid in the hot solution for 30 minutes.

If soaking does not remove all dirt, wipe the parts with a sponge soaked in lemon juice or a solution of citric acid prepared in a ratio of 1:3.

Table vinegar

When cleaning the hood parts with vinegar, be sure to use gloves, this will protect the skin of your hands from irritation.

• Soak a foam sponge in vinegar (do not take the essence!) and apply the product liberally to the contaminated parts of the hood. It will take 10-15 minutes for the fat to dissolve. After this time, remove any remaining vinegar and grease by rinsing the parts under water.

Lemon acid

• Prepare a concentrated solution of citric acid and apply it to the mesh and filters. It will take 15-20 minutes for the product to start working. After the greasy deposits have soaked and become soft, you need to clean the parts and rinse them in warm water.

If during the cleaning process you were not able to remove all the dirt, repeat the procedure again.

Cleaning external surfaces

The hood must be clean not only from the inside, but also from the outside. Not only do they remain on the surface of the device greasy spots, but also dust, which complicates the task and spoils the appearance of the kitchen. In this case, it is unacceptable to use abrasive powders and hard sponges, as this can cause scratches on the surface. How to easily clean the outer housing of the hood?

• Dishwashing liquid is suitable for these purposes. Apply it to a cloth or foam sponge and rub the surfaces generously. Leave the product on for 30-40 minutes to soften the fat, then clean the body. Heavy soiling can be removed using a rubber scraper; this will not damage the surface.

After cleaning, remove any remaining product from the surface by wiping it with a clean, damp sponge.

Cleaning the hood with a steam cleaner

Most in a simple way To clean the grate, use a steam generator.

Those who are not yet planning such a purchase can use cleaning chemicals or folk remedies. And owners of dishwashers can easily cope with the problem of grease using this unit.

How often should you clean your kitchen hood?

The frequency of washing the hood parts depends on how intensively the housewife uses the gas stove. The more often the family cooks, the more often the hood is cleaned.

Lifehack

• If there is Dishwasher and the grate is the right size, you can wash it along with the dishes once a week. Metal grate hoods are usually made of stainless steel, so such cleaning will not cause harm, but will save effort and time.

So that on aluminum or glass surface If the hood does not leave streaks, use window cleaner and a dry cloth.

With the right and timely care hood above kitchen stove will last you a long time and prevent the spread unpleasant odors from the kitchen throughout the apartment.