1. Base. Strapping and purlins for partitions - calibrated timber coniferous species with a cross-section of 150x100 mm (per edge), in one row, floor beams - calibrated softwood timber with a cross-section of 150x50 mm with a pitch of no more than 60 cm. (Distributed load over an area over 350 kg/m2) Fire-bio base treatment protective compounds not included. (Available as option)
2. Subfloors: calibrated softwood board 22 mm thick
3. Finished floors: board, planed, tongue and groove, 27 mm thick, chamber drying. (Replacement with 36 mm tongue and groove is available as an option). The floors of the terraces are calibrated timber with a cross-section of 100x40 mm, planed on the front side, laid through a gap.
4. Floor heights: First floor: 2.30 m Second floor: 2.20 m.
5. Walls and partitions. The frame of the walls and partitions is calibrated softwood timber with a section of 100x40 mm. The pitch of the racks is no more than 60 cm. Installation of diagonal stiffeners (braces) to impart rigidity to the frame. Frame timber natural humidity ATTENTION!
6. Insulation. The building is insulated with rolled mineral non-flammable Knauf insulation(Thermal conductivity λ0, W/(mK), no more than 0.040 according to GOST 7076-99), or equivalent. Thickness of insulation of floors and ceilings, attic walls (if any): 100 mm. Thickness of insulation (sound insulation) of internal frame partitions and interfloor ceilings (if any): 50 mm. (Insulation with slab insulation or Ecowool is available as an option)
WITH inside Insulation in insulated structures is laid with a membrane-type vapor barrier film (Nanoizol B, or a price equivalent) to prevent moisture from entering the insulation, which significantly improves thermal conductivity. WITH outside insulation is laid hydro- windproof film membrane type (Nanoizol A, or price equivalent)
8. Interfloor ceiling: Calibrated coniferous timber with a cross-section of 150x50 mm in increments of up to 60 mm (Distributed load over an area of more than 350 kg/m2) For a span of more than 4 m, a support beam (matitz) is installed FREE OF CHARGE, eliminating deflection and creaking of the floor.
9. Exterior finishing: the frame is sheathed with planed profiled boards (lining) 16x90(120) mm, softwood, chamber drying.
10. Interior decoration: The walls and ceilings are sheathed from the inside with planed profiled boards (eurolining) 12.5x90 mm, softwood, chamber drying.
11. Rafter system: calibrated softwood timber with a section of 100x40 mm, in increments of up to 1 m for a roof slope of more than 30 degrees. , and 150x40 mm with a roof slope of less than 30 degrees.
12. Lathing: Calibrated softwood board with a cross-section of 22x100 mm, 1-2 grades, with a membrane-type waterproofing windproof film (Nanoizol D or a price equivalent)
13. Roof extensions: 27-32 cm, hemmed with planed profiled boards (lining) of coniferous species, chamber drying, in 3 boards.
14. Roof: finishing coating Ondulin with a choice of colors (green, burgundy, brown), including all necessary roofing elements. (Metal tiles, bitumen shingles are available as an option)
15. Windows. Wooden frames, double glazing, imitation double-glazed windows, with pivoting sash. Dimensions according to the project.
16. Doors: Wooden, paneled, solid 2.05x0.8 m. with installation of platbands, hinges, slopes. (Iron front door available as an option)
The bowstring is made of planed softwood timber with a section of 150x100 mm, the steps are made of planed boards with a section of 200x40 mm. The staircase railing is being completed flat carved balusters.
18. Fencing: flat carved balusters
19. Drainage system:
Download (pdf, 577 Kb)"Turnkey winter cottage" package
×1. Base.
2. Subfloors:
3. Finished floors: High-quality (class AB) planed tongue-and-groove floor board 36 mm thick, chamber dried, or prepared for laminate: OSB 9 mm on calibrated coniferous boards 22x100 mm chamber drying, at the choice of the “Customer” The terrace floors are calibrated timber with a cross-section of 100x40 mm, planed on the front side, laid through the gap.
4. Floor heights: First floor: 2.40 m Second floor: 2.30 m.
5. Walls and partitions. natural humidity. (Kiln drying timber available as an option) ATTENTION! The frame is assembled in accordance with the Canadian Construction Code and Russian SNiP 31-105-2002. The strength of the connection of frame elements is achieved by following assembly technology, without the use metal corners, plates, staples.
6. Insulation. The building is insulated with roll ( horizontal surfaces) and slab (vertical and inclined surfaces) mineral non-flammable insulation Knauf (Thermal conductivity λ0, W/(mK), no more than 0.040 according to GOST 7076-99), or equivalent, Thickness of insulation of floors and ceilings, attic walls (if any): 150 mm. Thickness of insulation (sound insulation) of internal frame partitions and interfloor ceilings (if any): 100 mm. (Ecowool insulation is available as an option)
7. Vapor barrier and wind protection. On the inside of the insulation in insulated structures, a membrane-type vapor barrier film (Izospan V, Ondutis R 70, or an analogue) is laid to prevent moisture from entering the insulation, which significantly improves thermal conductivity. On the outside of the insulation, a membrane-type hydro-windproof film is laid (Izospan A, Ondutis A 100, or equivalent)
8. Interfloor covering:
9. Exterior finishing: the frame is sheathed with environmentally friendly OSB-3 8-9 mm, E-0.5 (E-formaldehyde emission class, class E-1 and below are certified for use in interior decoration of residential premises). On OSB, a membrane-type windproof film and a 50x20 mm block (Ventilated Facade technology) are installed, sheathed with planed profiled boards (lining) 16x 90 (120) mm, coniferous, kiln drying External finishing imitation timber, block house, siding
10. Interior decoration: The walls and ceilings are sheathed from the inside with planed profiled boards (Euro standard lining) 12.5x90 mm, coniferous, chamber-dried, over a membrane-type vapor barrier film.
11. Rafter system:
12. Lathing: Calibrated softwood board with a section of 22x100 mm, grade 1-2, with a membrane-type waterproofing windproof film (Izospan A, Ondutis A 100, or equivalent)
13. Roof extensions: 32-40 cm, hemmed with planed profiled boards (lining) of coniferous species, chamber drying, in 4 boards.
14. Roof: Ondulin finishing coating with a choice of colors (green, burgundy, brown), including all the necessary roofing elements. (Metal tiles, bitumen shingles are available as an option)
15. Windows. Plastic double glazed window white, double glazing (single-chamber) Dimensions according to the project. Window sills and ebbs are included. The gaps are filled polyurethane foam.
16. Doors: Wooden, paneled, solid 2.05x0.8 m. with installation of platbands, hinges, slopes. Iron entrance door. (StroyGOST 5-1, or equivalent) The gaps are filled polyurethane foam.
17. Stairs to the second floor (if available): The bowstring is made of planed coniferous timber with a cross-section of 200x50 mm, the steps are made of planed boards with a cross-section of 250x50 mm, the staircase fencing is made of turned factory-made balusters.
18. Fencing: open terrace, balcony is performed flat carved balusters or planed timber with a cross section of 40x100 mm, at the request of the customer.
19. Drainage system: Not installed (available as an option)
Download (pdf, 577 Kb)Complete set "Winter cottage under roof"
×1. Base. The base is made in 2 rows of timber. The first row is timber 150x100 mm (height 100 mm). Second row: strapping is calibrated softwood timber with a cross-section of 150x150 mm, purlins for partitions and floor beams are calibrated softwood timber with a cross-section of 150x100 mm (height 150 mm) with a distance between beams of no more than 60 cm. (Distributed load over an area of 550 kg/m2) Treatment of the base with fire-bioprotective compounds is not included. (Available as option)
2. Subfloors: calibrated softwood board with a section of 22x100(150) mm
3. Finished floors: Not fulfilled.
4. Floor heights: First floor: 2.40 m Second floor: 2.30 m.
5. Walls and partitions. The frame of the walls and partitions is calibrated softwood timber with a section of 150x40 mm. The pitch of the racks is no more than 60 cm. Installation of Oriented Strand Board (OSB-3, 9 mm) on the outside to stiffen the frame. Frame timber natural humidity. (Kiln drying timber available as an option) ATTENTION! The frame is assembled in accordance with the Canadian Construction Code and Russian SNiP 31-105-2002. The strength of the connection of frame elements is achieved by following assembly technology, without the use of metal corners, plates, or staples.
6. Insulation. Not insulated. It is recommended to carry out insulation immediately before interior finishing, in order to avoid dampening of the insulation.
7. Vapor barrier and wind protection. Not executed.
8. Interfloor covering: Calibrated coniferous timber with a cross-section of 150x50 mm in increments of up to 60 mm (Distributed load over an area of more than 350 kg/m2) For a span of more than 4 m, a support beam (matica) is installed FREE OF CHARGE, eliminating deflection and creaking of the floor.
9. Exterior finishing: the frame is sheathed with environmentally friendly OSB-3 8-9 mm, E-0.5 (E-formaldehyde emission class, class E-1 and below are certified for use in interior decoration of residential premises). Exterior finishing imitation timber, block house, siding, as well as replacing OSB with IZOPLAAT boards are available as an option.
10. Interior decoration: Not executed.
11. Rafter system: calibrated softwood timber with a cross-section of 150x40 mm, the distance between the rafters is no more than 0.8 m.
12. Lathing: Calibrated softwood board with a section of 22x100 mm, grade 1-2, with a membrane-type waterproofing windproof film (Izospan A, Ondutis A 100, or equivalent)
13. Roof extensions: 32-40 cm, not hemmed.
14. Roof: Ondulin finishing coating with a choice of colors (green, burgundy, brown), including all the necessary roofing elements. (Metal tiles, bitumen shingles are available as an option)
15. Windows and doors: Not installed. Openings are made according to the project.
16. Stairs to the second floor (if available): Not executed.
17. Fencing: There is no open terrace or balcony.
18. Drainage system: Not installed
Download (pdf, 678 Kb)Complete set "Turnkey residential building"
×1. Base. The base is made in 2 rows of timber. First row - timber 150x150 mm Second row: strapping - calibrated softwood timber with a cross-section of 200x150 mm (height 200 mm), purlins for partitions calibrated softwood timber with a cross-section of 200x100 mm (height 200 mm) and floor beams - calibrated softwood timber with a cross-section of 200x50 mm (height 200 mm) with a distance between beams of no more than 60 cm. (Distributed load over an area of more than 600 kg/m2) All wooden elements of the base are treated with a fire-bioprotective composition.
2. Subfloors: calibrated softwood board with a section of 22x100(150) mm, 1st grade.
3. Finished floors: High-quality (class AB) planed tongue-and-groove floor board 36 mm thick, chamber-drying, or preparation for laminate: OSB 9 mm on calibrated softwood board 22x100 mm chamber-dried, at the choice of the “Customer” Open terrace floors (if available) - calibrated block cross-section 100x40 mm planed from the front side, laid through the gap.
4. Floor heights: First floor: 2.50 m Second floor: 2.40 m.
5. Walls and partitions. Wall frame - calibrated softwood timber with a cross section of 150x40 mm plus calibrated timber 50x50 mm on the inside of the wall perpendicular to the posts of the main frame (Technology "cross insulation"), the frame of the partitions is calibrated softwood timber with a section of 100x40 mm. The pitch of the racks is no more than 60 cm. Installation of oriented strand board on the outside to stiffen the frame. Frame timber natural humidity. (Kiln drying timber available as an option) ATTENTION! The frame is assembled in accordance with the Canadian Construction Code and Russian SNiP 31-105-2002. The strength of the connection of frame elements is achieved by following assembly technology, without the use of metal corners, plates, or staples.
6. Insulation. The building is insulated with slab mineral insulation based on stone wool Rockwool Light Batts Scandic (Thermal conductivity λ0, W/(mK), no more than 0.040 according to GOST 7076-99) Thickness of floor and ceiling insulation, attic walls (if available): 200 mm. The thickness of insulation (sound insulation) of internal frame partitions is 100 mm and interfloor ceilings (if any): 150 mm. (Ecowool insulation is available as an option)
7. Vapor barrier and wind protection. On the inside of the insulation in insulated structures, a vapor barrier film of the Ondutis R 70 Smart membrane type is laid with gluing of the membrane joint seams to completely prevent moisture from entering the insulation, which significantly improves the thermal conductivity and durability of the insulation. On the outside of the insulation, a hydro-windproof film of the Ondutis A 100 membrane type is laid.
8. Interfloor covering: Calibrated coniferous timber with a cross-section of 200x50 mm in increments of up to 60 mm (Distributed load over an area of over 600 kg/m2) For a span of more than 4 m, a support beam (matica) is installed FREE OF CHARGE, eliminating deflection and creaking of the floor.
9. Exterior finishing: the frame is sheathed with environmentally friendly OSB-3 8-9 mm, E-0.5 (E-formaldehyde emission class, class E-1 and below are certified for use in interior decoration of residential premises). A membrane-type windproof film and a 50x20 mm block (Ventilated Facade technology) are installed over OSB and covered with planed profiled boards. (imitation timber) 18x140 mm, coniferous species, chamber drying. Exterior finishing block house, siding, as well as replacing OSB with IZOPLAAT boards are available as an option.
10. Interior decoration: The walls and ceilings are sheathed from the inside with planed profiled boards (Euro standard lining) 12.5x90 mm, coniferous, chamber-dried, using a membrane-type vapor barrier film with sealing of joints.
11. Rafter system: calibrated coniferous timber with a cross-section of 200x40 mm, or calibrated softwood timber with a cross-section of 150x40 mm (depending on the project and type of roof) with increments of up to 0.6 m.
12. Lathing: Calibrated softwood board with a section of 22x100 mm, grade 1-2, with gasket waterproofing film membrane type (Izospan D or equivalent)
13. Roof extensions: 42-50 cm, hemmed with planed profiled boards (lining) of coniferous species, chamber drying, in 5 boards.
14. Roof: finishing coat metal tiles Monterrey, polyester, 0.45 mm thick, with a choice of colors (RAL 3005 dark red, 3011 red, 5002 blue, 6005 green, 7004 grey, 7024 dark grey, 8017 brown) including all necessary roofing elements. ( Bituminous shingles Dock Pie available as an option)
15. Windows. White metal-plastic double-glazed window, profile 70 mm, triple glazing(two-chamber), Window sills, ebbs, mosquito net- included. Dimensions according to the project. ( Double glazing in wooden frame available as an option. Painting possible wooden window high quality materials in production)
16. Doors: Wooden, paneled, solid 2.05x0.8 m. with installation of platbands, hinges, slopes. Insulated iron entrance door. (Garda)
17. Stairs to the second floor (if available): The bowstring is made of planed coniferous timber with a cross-section of 250x60 mm, the steps are made of planed boards with a cross-section of 300x50 mm, the staircase fencing is made with turned factory-made balusters.
18. Fencing: open terrace, balcony turned balusters factory-made or planed timber with a cross-section of 40x100 mm, at the request of the customer.
19. Drainage system: Plastic is installed drainage system Docke Premium is available in white, red, gray or brown.
Download (pdf, 577 Kb)Housing made from inexpensive frame-panel structures is built quickly and is relatively inexpensive. Projects frame houses 6 by 6 are extremely popular. The fact is that the ratio of all important indicators (construction price, usable area of housing) of these objects is recognized as optimal.
Already from the name of the object we can conclude that it is a rigid frame, which is sheathed on the outside. The possibility of quick construction and the low cost of such a home have long been made this type construction is extremely popular.
There are some nuances that you should pay attention to special attention:
- Not a very good indicator of environmental cleanliness. It consists of the following: synthetic, large number adhesive composition, products for wooden elements. Responsible material manufacturers carefully monitor the content of harmful formaldehyde when using the substances they require. When dealing with unfamiliar suppliers, it is difficult for the average consumer to recognize various technologies violations of the manufacturing process.
- A one-story house 6 by 6 is almost impossible to remodel. It is manufactured in a factory according to the selected design, and once the work is completed, changes are not possible. Do-it-yourself “corrections,” or corrections, can have a significant impact on the overall safety of a structure. In this regard, homemade panel elements have certain advantages: they are easier to correct or replace if necessary.
- The frame is made of wood, and like any type of wood, it is a rather capricious material. The insulation placed inside the walls serves as a bait for various kinds rodents and pests. This can be easily solved - with a certain amount chemicals. But as noted above, this does not at all improve the quality of the environmental friendliness of the building.
- Panels 6 6 have quite an impressive weight. Accordingly, to simplify the assembly of the frame, it is important to use technology and a qualified approach. At self-construction It is also important to strictly follow all recommendations, strictly following the existing plan. Otherwise, not only the appearance building, but also its safety.
We build it ourselves
How possible is it to build a 6 by 6 with a veranda without involving professionals, and without using factory “semi-finished products” for construction? In fact, this is quite possible; moreover, it is a frequently used practice.
Project
House project Without careful detail it is impossible to build even a simple one. Without the necessary package of papers, any erected structure is doomed to demolition, sooner or later. The point is not that they want to rip off additional money from you, and not in someone’s tyranny. The reason lies elsewhere - without the research of qualified professionals, projects of even frame structures can carry real threat safety of people.
On initial stage, before starting work, you will have to contact the architectural department or design bureau for a project or drawing frame house.
There specialists will sort out your specific situation regarding technical specifications, preferred type, layout and even appearance of the future home, will produce necessary calculations for a frame house.
When permission is obtained, a verified and competent project is approved much more successfully than a clumsy homemade sketch or sketch.
Material: what to prefer?
Building a house with your own hands It’s probably not worth explaining that the final result directly depends on the quality of the selected raw materials. construction work:
- To make the frame, certain sizes are selected. Its cross-section must be such as to withstand the expected loads at any time of the year. Most suitable material cross section from 20 centimeters. This type is usually used in the construction of winter-type dwellings.
- What to choose for the construction of durable and? What materials are optimal for a 6 by 6 frame house? This could be, for example, fiberboard or. Their main difference lies in the components - more or less large sawdust. Double or special extruded is used as a filler.
- The design is also frame. You can use a lighter one with a smaller cross-section. Particular attention is paid to its quality: it should not have any flaws, even of natural origin. Roof design features are dominant when choosing. The point is the angle of inclination: the material should be more structural, the steeper the roof slope.
All wooden elements frame house 6 by 6 must be properly prepared before being used. Impregnation and treatment with various protective compounds will protect the wood from pests and damage.
Foundation of the house
Careful frame house IR is much lighter in weight than a similar-sized structure made from solid logs or bricks.
For this reason, it does not require a monolithic foundation. What could it be?
All columnar bases have one important drawback– cold floor in the room. To avoid such trouble, you will have to pay attention to its thorough insulation.
Walls
A frame house can be compared to a kind of multi-layered pie, consisting of many different layers, including protective ones.
- main of ;
- indispensable;
- panel made of wood-based materials;
- required layer ;
- lathing, one of the types of decorative.
Inside, under the chipboards, it is placed. Its role can be played by a special diffuse membrane. The design of such a “pie” is easy to make with your own hands. The layers can be installed in stages, or you can make them in advance, and only then insert the completed panels into their intended place.
Rafters
The structure of a frame house does not differ from that for roofs of objects that are heavier in weight. The system is the same - a set of farms, rafter legs, and pediments.
It was noted above that the magnitude of the slope angle determines the nature of the material. In order for snow to easily fall off the roof without lingering on it, it is better to use options with metal for covering - or.
DIY installation: common mistakes
Before starting construction work, it would be a good idea to evaluate own strength. Amateur builders who do not have professional skills often make fatal mistakes, the consequences of which can be more serious than it seems at first glance. This not only reduces the operational comfort of the home, but even its collapse in extreme cases. What's important?
Wood for construction must be of proper quality. Wood normal humidity, or factory-dried, deforms much less, thereby ensuring structural strength. This provision does not apply to untreated, raw whips. What are the risks of using unprepared or substandard material?
The frame is the basis of the entire structure. Consequently, torsion, bending or increased stress of any element will cause deformation of the entire structure. Both small and partial destruction, and complete collapse of the entire structure are possible. How to identify defects during purchase? The edges of such beams can be dirty and crooked; if iodine is dropped onto the surface, it will turn blue.
The quality of a frame house also depends on the price of the preferred materials. It’s better not to skimp on the rigidity of the frame; it may end up costing you more. Diagonal elements located between upright supports serve as structural reinforcement. Saving on them is strictly contraindicated, even if a very small house is planned.
It is necessary to take into account the loads coming from above: the weight of the structure, weather conditions, shrinkage. To increase strength, you can do additional gains criss-cross.
Is it possible to properly arrange window and door openings with your own hands? This is also an important part of the job. Frame shrinkage is noticeably less than that of log walls or walls, but it is still there. If you do not take this into account, you can introduce some risks in subsequent operation.
Window installation Before ordering double-glazed windows, you must invite a professional measurer and. A specialist will be able to take competent measurements and assess the condition of the openings. It’s not worth it for such a seemingly trifle. Moreover, most manufacturers provide such a service virtually free of charge. Or rather, it was initially included in the price.
Purchased and arrived at construction site special attention should be paid to the material. It must be processed, stored properly, and ventilated. Proper handling of the material will ensure that the final product is a high-quality structure that will be used for a long time and comfortably.
If all of the above has frightened the potential builder, disabusing him of his own capabilities and strengths, you can consider a turnkey service. Such a frame house will cost more, but in this case the price is justified by the reliability and quality of further operation.
But there’s no need to be scared in vain either. Cozy frame house 6 square meters, with a serious and competent approach, it will not become an insurmountable stage for a not lazy and handy craftsman who has carpentry skills and knows how to use a tool. The main thing in this is to correctly assess your own capabilities and use the recommendations and rules for the manufacture of frame structures. Then built with my own hands the home will become a source of joy and pride for its owner.
Frame-panel structures are already for a long time used everywhere in the construction of private houses. The main advantage that attracts developers is the very short terms construction. Projects of country cottages with dimensions of 6 x 6 meters are considered very popular due to the optimal ratio of usable area/construction price.
Project of a 6x6 frame house with an attic and veranda
Let's look at a 6 x 6 frame house in more detail, and also evaluate the complexity of building such houses with your own hands.
In order to understand what makes them so popular among developers, it is necessary to look at some of their features:
- The light weight it has, even if it comes with an attic. It's no secret that when constructing private houses, the lion's share of the cost of the construction estimate goes to laying the foundation. According to experts in the field of pricing and builders, the cost of the foundation for a house can reach thirty percent of the cost of the entire construction. But such costs await only those who are going to build capital buildings, for example, . But as for frame cottages, then things are more encouraging here.
Project frame-panel house with plans and visualizations
Projects and drawings of frame houses with an attic, as a rule, involve the construction of lightweight types of foundations. This will accordingly contribute to the fact that the price of construction will decrease. Typically, projects involve a pile foundation. In addition, the light weight of frame houses ensures that the load on the ground will be minimal. Consequently, a two-story frame house or can be erected on plots with any type of soil. Despite this, if there is unfavorable conditions on the site, it is necessary to order a drawing and design so that specialists can evaluate everything possible risks. The price of construction will, of course, increase because of this, however, you will not have to worry about problems in the future;
- Simplicity installation work. The construction of frame houses is carried out using a very simple technology that excludes any wet processes, and accordingly the installation price will be low.
Installation consists of constructing a frame onto which the sheathing is subsequently attached. These works can be done for free with your own hands, and it is not at all necessary to hire someone for this. professional builders. Step by step instructions on construction can be easily found on the Internet. You can collect such houses at limited area, which is very attractive to builders involved in the sale of frame houses. This technology for building houses allows you to fulfill any desires of the developer, and the building can be of almost any shape; - Dachny two-story house or one-story house with an attic it does not shrink. Shrinkage occurs due to the presence of moisture in wooden building materials, which is a serious disadvantage. Because of this finishing work can begin only after some time has passed, which in certain cases can reach one year.
Ready frame project two-story cottage 6x6
As for frame houses, finishing work can begin almost immediately;
- Excellent performance And long term services. Frame houses retain heat very well, which helps save thermal energy. You can heat frame houses in an economical mode, that is, most of the time you just maintain heat. The walls of frame houses “breathe”, so the microclimate in the home will be very comfortable for household members. Thanks to this, the coolant may not heat up too much, and the operating time of air conditioners can also be reduced. hot weather. Wall decoration can be done by anyone finishing material. Frame construction does not imply deformation during soil movement or subsidence under its own weight. If redevelopment is carried out in a frame house, there is no need to worry about the uneven distribution of the load on the foundation;
- Low installation cost. As noted above, for pile foundation It is not necessary to carefully study the properties of the soil, which increases the cost of construction. In addition, the labor costs of constructing a frame house are much less compared to, for example, brick buildings. Also worth noting low cost building materials, from which the foundation and frame of the building are assembled. Frame buildings can be easily repaired. For example, if it is necessary to add an additional pile to the base structure, you can minimal costs perform this procedure, which cannot be said about repairs strip foundations, where the price of repairs significantly hits your pocket. As for wall repairs, things here are also much simpler than in the case of repairs of brick houses.
Price of a house with insulation 150mm min. cotton wool and finishing 376t.r.
Price of a house with insulation 150mm min. cotton wool, finishing and foundation 436t.r.
Price of a house with insulation 150mm min. cotton wool, finishing, foundation, electrical, plumbing and water supply 493t.r.
Standard insulation 150mm walls, 200mm basalt roof min. cotton wool, max. 250mm.
Project price for self-assembly 6t.r. Download estimate and read
If for some reason you don’t want or can’t build a house yourself according to our design, then we can do it all for you, inexpensively and in the shortest possible time. For more information about the prices and benefits of turnkey construction, read the section " Turnkey price ".
Frame house 2 floors (living attic)
Download, Project KD-17 (comfort) 0.5 Mb (pdf) >>> detailed description.Drawings of a frame house 6x6m 72m/sq - small, inexpensive, but comfortable home. Most inexpensive house from our collection of projects, such a house can be built on your own or by ours very quickly, the house can be used both for summer holiday, and for going out into nature in spring and autumn, and, if desired, in winter period vacations and vacations. The house has everything you need for a comfortable stay at any time of the year.
The finishing of the house can be changed according to your preferences, according to the project: external clean OSB and internal fine finishing GKL are included in the cost of the project. Also included in the price of the project is the foundation, insulation 150mm min. cotton wool (possibly up to 250mm), electrical wiring and installation products, automatic water supply, sewerage with installed plumbing.
First floor 36 m2: Ceiling height 2.5m, Living room 12.5m2, Kitchen 8.5m2, bathroom 3m2, ridge height 7.4m.
Second floor 36 m2: Ceiling height 2.5m, Bedroom 10m2, Children's bedroom 10m2, Hall 3m2, Wardrobe 3m2.
To enlarge the picture, click on it.
Appearance options:
Any finish is possible, see options, project KD-12, KD-151 and KD-171.
Elevations:
Foundation for this house:
according to the MZLF project 50h x 40w.
possible piles (screw, bored, etc.) 15 pcs. 
By clicking on the photos below, you can see photo galleries of houses built according to this project by our builders or by customers themselves (see notes in the galleries):
The average market price of such a house is 4 times higher than ours.
Order a project
To place an order, select the type of foundation and others possible options, then click the "Order a project" button. In the form that opens, enter your email and other required information correctly. If the order is placed correctly, then immediately after processing the order by our specialist, you will receive an order confirmation by email with details and payment options.
Project KD-17
Tape (MZLF) Piles
Project price 6t.r.
(set of working diagrams and components: frame house, foundation, electrical engineering, estimate, etc.)
Order a project
Frequently asked questions from clients:
What to do if you need to change something in a project you like?