After completing the roof installation work, mandatory finishing of the cornice is necessary. This will protect it from the effects of external natural factors - rain, snow, strong wind, prevent nesting of birds, the appearance of harmful insects and extend the life of the roof. Today, special elements are used for these purposes - soffits for roofing: sizes, prices and manufacturers, materials used and installation tips will be presented in this article.
The roofing of the building was always carried out. If this is not done, then the roof will quickly become unusable, and the house itself will be cold and damp. There are a large number of different materials that can be used to finish the facade and roof:
- wooden plank. You can use edged or unedged wood. Most often, preference is given to coniferous species. It is inexpensive and accessible. Before installation, the wood is treated with an antiseptic. After this, keep in a warm, well-ventilated place for 30 days. When the boards are directly laid, slots for ventilation are provided at the joints;
- lining. Available and inexpensive material. For outdoor use, it is chosen with moisture-resistant and antiseptic characteristics. The lining is laid tightly to each other. However, a gap is provided between the eaves and the wall of the house for ventilation;
- siding panels. This type of material appeared relatively recently. However, it has earned popularity due to its affordable cost and long service life. A special feature of siding installation is the need to install it perpendicular to the wall of the house. Otherwise, the panels may sag under their own weight;
- plywood sheets. Before installation, this material is subjected to a special moisture-repellent impregnation. Then they cut it into strips of the required size and then begin to carry out the work;
- . Aluminum and galvanized plates are easy to install and are durable. However, they have a very high cost;
- soffits. Convenient and reliable material that does not need to be pre-prepared before installation. Any home craftsman can install roof overhangs with soffits. To perform these works you do not need special knowledge.
Types of soffits for roofing
Modern manufacturers divide roofing soffits according to the design features and materials from which they are made.
Existing types:
- non-perforated solid. In appearance it resembles a solid smooth panel. This type is recommended for pouring gable overhangs;
- partial perforation. This type is distinguished by the presence of perforations in the middle of the panel. Using this type allows you to get good ventilation. This makes it possible to prevent the appearance of mold, mildew and condensation. Great for finishing any area of the cornice;
- completely perforated. This type is recommended for finishing overhangs with cornices, canopies, and ridges. Perforated soffit is the best choice for the roof of a gazebo, porch or veranda. This will allow you to get the necessary ventilation.
The difference between them is clearly visible in the photos of soffits for roofing, of which there are now many on the Internet. Based on them, you can choose the type that meets the requirements of the finishing and roof configuration. In addition to design features, soffits are divided according to the materials used.
Materials for making soffits
The size and cost of spotlights is influenced by the material used for their manufacture. Popular brands chosen for this are aluminum, copper, metal and plastic.
Let's look at them in more detail:
- perforated copper soffits are the most expensive. They are distinguished by a small plate thickness and a long service life of up to 150 years. At the same time, the spotlights are environmentally friendly, resistant to aggressive environmental factors, and do not require constant careful maintenance;
- Aluminum roof soffits are inexpensive and resistant to temperature changes. Thanks to a special coating, they are not subject to corrosion. The thickness of the plates ranges from 0.3 to 0.6 mm;
- Stainless steel soffits are considered the most durable. They are distinguished by their resistance to moisture and temperature changes. To decorate roof eaves with metal soffits, both perforated and solid plates can be used. The price of metal soffit is the lowest among other types;
- Polyvinyl chloride is used for the manufacture of plastic spotlights. They are distinguished by their low price and light weight. Such soffits can withstand temperature changes well. They are not susceptible to fungus and mold, but may turn yellow when exposed to direct sunlight.
Helpful advice! When choosing soffits for roof lining, it is necessary to take into account the type of structure. Metal elements will weigh down the structure and put pressure on the foundation. Therefore, in frame houses it is better to choose plastic for finishing the roof.
Soffit sizes
Oddly enough, today there are no standardized parameters for spotlights. Each manufacturer offers the client its own sizes. This allows you to choose exactly what is best suited for a particular cornice. After all, it is impossible to trim the panels.
Most often, companies offer spotlights with dimensions of 360x30 cm. These parameters are convenient and practical. Knowing them, you can easily calculate the required number of panels. They fit well, forming a beautiful pattern on the cornice.
Domestic companies producing spotlights offer panels with a width of 50 to 80 cm. If desired, you can also find wider models.
The thickness of aluminum panels ranges from 0.3 to 0.6 mm. But vinyl ones can have the following parameters:
- thickness from 1 to 1.2 mm;
- width from 2.2 to 3 cm;
- length from 30 to 38.5 cm.
Helpful advice! It should be noted that the parameters of domestic and foreign manufacturers differ from each other. Therefore, when purchasing spotlights, you need to carefully study their sizes.
Advantages of soffits for roofing
Lining the roof with soffit has a number of advantages compared to other types of finishing. The main advantages of using this material include the following points:
- high resistance to mechanical stress;
- no special care requirements (it is enough to wash with water twice a year);
- resistance to moisture, direct sunlight and high temperatures;
- wide range of applications (perfect not only for exterior, but also for interior decoration);
- ease of installation;
- resistance to fungus and mold;
- excellent appearance;
- protection not only for the roof, but also for all communications located under it;
- Possibility of use at different temperatures, from -60 to 120°C.
In addition, they are environmentally friendly for human health and have a good appearance.
Disadvantages of spotlights
Like any material, roof soffits have a number of disadvantages that you need to be aware of when choosing them for yourself. Experts include:
- the need for constant monitoring of the condition of the plates. Perforated soffit can become clogged with various small debris. Under the influence of strong gusts of wind, the plates become loose and come out of the grooves. All soffits should be thoroughly inspected every year. And once every five years they require complete or partial replacement;
- the cost of this material is quite high. If we compare it with regular corrugated sheeting, then the latter can be purchased at 2 times cheaper;
- inability to change the size of the soffit if necessary. So, when laying siding or corrugated sheeting, the material can be reduced using available means. You can't do that with a soffit. This is due to the presence of perforations in its design. Their violation leads to deterioration in the performance characteristics of the material.
Helpful advice! If the roof has unusual angles or curves, then perforated soffits are not the best choice for finishing the eaves.
Soffits for roofing: sizes, prices and manufacturers
Today, various domestic and foreign companies produce roof soffits, prices for which range from 280 to 1100 rubles/m. Due to the fact that this material is quite expensive, experts recommend purchasing it only from well-known manufacturers.
Overview of roofing soffit manufacturers
There are a significant number of manufacturers of finishing plates on the construction market; let’s look at the most famous ones in more detail.
Döke. The homeland of this manufacturer is Germany. We have known the products of this brand since 2006. The company offers customers to buy soffits for roofing in several sizes: 3050x305 and 3050x151 mm. You can choose white, red or chocolate plates. A distinctive feature of this manufacturer is that the spotlights are equipped with additional elements that are necessary during installation.
Gentek. The company is American, although it has been operating in our market for several years. It produces aluminum soffits for roofing, the price of which is the highest in the building materials market. However, when purchasing a plate, the client immediately receives a complete set with additional elements. He won't have to buy them separately. Kit includes j-rail, j-bevel, wind strips, finish strip and aluminum texture strip. Soffits of this brand come in brown and white. The size of the plates is 3660x306 mm.
Grand Line. This is a Russian manufacturer. It offers metal soffits for roofing, the price of which is affordable. You can choose brown or white color of the products. The dimensions offered by the manufacturer are 3000x305 mm. The advantages of plates of this brand are a long service life (up to 50 years), resistance to sunlight, shock, invisibility of joining and good flexibility.
Holzplast- a company from Germany. It offers vinyl soffits that are made by pressing. The use of co-extrusion technology allows the manufacturer to produce two- and three-layer soffits. The dimensions of the plates are 3660x266 m. The client can choose white, chocolate or golden oak.
Royal Europa- Polish brand. You can buy roof soffits from this company in a variety of colors. The dimensions of the plates are 3660x305 mm. The difference between this manufacturer is the use of organotin-type stabilizers. They are absolutely safe for human health and the environment.
Related article:
Types of coatings. Comparative characteristics, disadvantages and advantages. Classification of materials for roof construction.
Alta Profile. This company is domestic. A distinctive feature of this brand is its good price-quality ratio. Its soffits are resistant to direct sunlight and low temperatures. The dimensions of the plates are 3000x230 mm.
Odintsovo Light Structures Plant offers domestic buyers metal perforated soffit, the price of which is affordable. At the same time, the quality remains high. The plates have dimensions of 3000x325 mm and are available in a wide range of colors.
Helpful advice! When deciding to hem the roof eaves with soffit, you should not chase the popularity of the manufacturer. Our domestic companies offer materials of the same quality at an affordable price and with excellent performance characteristics.
Vinyl, metal and aluminum soffits: product price
The table shows the most popular manufacturers of spotlights and their cost depending on the material:
| Manufacturer | Cost, rub. |
| Vinyl | |
| Belarusian manufacturer | from 280 |
| Vox | from 260 |
| Dock | from 330 |
| Vinylon | from 360 |
| FineBer | from 360 |
| Mitten | from 600 |
| Metal | |
| Grand Line | from 400 |
| Aquasystem | from 580 |
| Aluminum | |
| Aquasystem | from 790 |
| Gentek | from 1100 |
All presented models have certificates guaranteeing product quality and high performance characteristics.
How to line a roof with soffit?
Modern construction offers two options for lining the cornice with soffit. The choice of one of them depends on the personal preferences and desires of the home owner. However, both options require preparatory work. They come down to insulating the building from the outside. After this, you can buy soffits for roofing and begin installing them.
Soffit installation methods
There are two ways to lay the plates.
Classic binder. In this case, the usual horizontal wooden box is installed. An additional board must be installed between the rafters. The edges of the plate will be attached to it. The soffits are laid along the wooden frame. One edge of the plate is fixed to the lower section of the rafters, and the second - to the additional board laid. In those corners where the roof slopes touch, it is necessary to secure the ends of the boards. The joints obtained in this way are located from the corner of the walls to the angle formed by the slopes.
This design solution makes it possible to obtain a rigid structure that is resistant to external influences. It does not depend on the walls. To ensure reliable installation of soffits on the roof eaves, you need to purchase special corners and plates for metal. However, quite often ordinary screws are used to secure them.
Hemming along the rafters. This option should be chosen when the roof of the house has a slight slope. In this case, the angle of the roof slope coincides with the angle of the sheathing. The plates are fastened to rafters running parallel to the walls of the house. If the lower part of the rafters has an uneven surface, leveling is done using an additional board.
The classic hem is most often used. It is easy and quick to install. It takes more time to hem the rafters.
Additional elements for installation
To carry out the finishing work, you will have to not only buy soffits for the roof, but also purchase a number of additional elements for them. Some manufacturers offer the entire set at once. However, this increases the price of soffits for roof lining.
Additional elements used in finishing work:
- finishing line. It is used at the final stage, after all panels and additional elements are installed. She supports the spotlights. In addition, the finishing tape is used to design inclined lines at the joints of the spotlights;
- j-chamfer. Its purpose is to protect the ends of the planks from the wind and give the structure the necessary rigidity;
- j-profile. Used when installing closed overhangs. The soffits themselves are attached to it;
- h-profile. Its purpose is to connect the soffits with the rafters and beams of the roof;
- profiles for designing external and internal joining corners.
The listed elements are not required. Their number can increase and decrease depending on the roof of the house, installation features, etc.
What is needed for installation
The technology for installing soffit work is quite simple and understandable. It is not necessary to invite a specialist to perform it. It is enough to carefully study the installation video and adhere to it during installation work. However, you cannot do without a certain set of tools and spare parts:
- profiles for fastening must be purchased as a complete set. Otherwise, you should not start work;
- sharp carpenter's knife. With its help it is convenient to install the plates into the grooves;
- hacksaw for metal;
- marker with built-in self-tapping screw;
- ruler and screwdriver;
- ladder or for working at height.
It is more convenient to carry out installation work in pairs. This will not only speed up the process, but also make it much easier.
Sequence of work
Above are two options for installing spotlights. For beginners, the classic one will be easier and more understandable. Installation on log houses has a number of features, so it is best to carry it out to a specialist.
Below are step-by-step instructions for lining the roof eaves with soffit:
- both plastic and metal panels are installed on a wooden frame. To make it, a timber beam with a cross-section of 5 cm is used. You should not take a tree with a larger or smaller diameter. A thick beam will make the roof structure heavier, and a thin beam will not withstand the influence of external forces (strong wind or heavy snowfall);
- Before fastening the beams, it is necessary to carefully mark the wall of the house. In this case, be sure to mark where the internal grooves and fastenings will be located. When installing the spotlights, the marks must completely match. This will ensure the surface of the cornice is even;
- After marking, the wooden beam is installed. In this case, it is necessary to use a building level. The owner decides how the beam will be fixed to the wall. If the structure is brick, then you can use nails and simply nail the wood. If the house is made of wood, foam blocks or other material, then it is better to use a screwdriver or install dowels;
- A supporting profile is installed on the timber. It has a J-shaped groove. Soffits will be installed in it. The panels have the same groove. This provides the necessary rigidity of the future structure;
- the next step is to install the sheathing panels. You can use nails or screws to install them. There is no need to achieve a tight fit between the panels. There should be a small gap between them. You don’t have to worry about cold wind blowing in or moisture getting in there. During subsequent operation, this gap will eliminate itself;
- The final stage is the installation of finishing tape at the joining points.
After installation is completed, it is recommended to treat the resulting surface with protective enamels for external use.
Roofing is an obligatory and necessary step when finishing the roof. This will ensure the safety of the roof frame from the influence of external natural factors, the appearance of harmful insects and birds. The latter can cause significant damage to the wood used. In addition, unformed eaves make the house damp and cold, which, in turn, leads to increased heating costs.
Roof soffits are necessary to give the building a complete look: they are used for lining awnings, ridges, and cornices. This element is designed to protect the space under the roof from precipitation, birds and insects. In addition to the protective function, soffits also perform a decorative function, as they mask possible fastenings and air ducts.
Roofing soffits
Roofing soffits can significantly increase the service life of a roof. These products can be made from different materials. Depending on the overall design of the building, you can choose products made from:
- Copper;
- Natural wood;
- Aluminum coated with a protective film.
Note that the cost of roofing soffits depends on the raw materials used in the production process: metal or aluminum are more expensive than plastic-based soffits.
Types of soffits for roofing
There are several main types of roofing soffits:
1. Perforated soffits. Usually used for hemming protruding parts of the roof (canopies, canopies, gables).
2. Partially perforated. Designed for street decoration. Provides the best ventilation for the under-roof space.
3. Smooth ceiling panel designed for interior use.
Whatever type of spotlights you choose, it is important to carry out the installation work correctly. If you don’t dare carry out the installation work yourself, you can always turn to the services of professional installers.
Buy perforated soffits for roofing in Moscow
In the catalog of the building materials store Krovla.msk you will find various types of soffit, differing in affordable prices. Please note that all products presented in our catalog (
The main collection of Aquasystem spotlights is made of high-quality galvanized steel, 0.45 mm thick, with a polymer coating. Also, Aquasystem soffits are made from aluminum and copper.
What is a soffit? A soffit is a strip of vinyl or metal siding, with or without holes for air circulation.
Soffits are intended for lining roof overhangs along the eaves and gables.
They perform decorative and protective functions, give a beautiful appearance, and ensure a long service life of the roofing covering and building structural elements.
Soffits are manufactured in three versions: without perforation, with partial perforation and fully perforated. The use of one or another soffit configuration is determined by the type of roofing and the characteristics of the building structure.
Temperature range of operation and installation possibilities from -60°С to +120°С.
Aquasystem soffits look stylish and last a long time!
You can buy soffits in Moscow by filling out an application
Plastic soffits appeared on the Russian market relatively recently. At first they were purchased only as components for vinyl sidings, but soon the products began to be used in the installation of roofs of any type, regardless of the material used for finishing the facade.
Plastic soffits, or PVC soffits, are presented by both Russian and foreign manufacturers. Most of them produce products in white and brown colors.
Main settings
Soffits are used for lining downward horizontal surfaces: pediments, cornices, canopies.
The composition of the soffit material is similar to conventional vinyl siding.
Plastic Features:
- The material is flexible.
- Easily trimmed.
- Resistant to corrosion and rotting.
- Withstands temperature fluctuations over a very wide range - from -50 to +50 degrees.
- The service life is more than 30 years.
- It is very easy to care for the plastic surface: just clean it from dust from time to time.
- The length of the panels is standard (300, 305, 306.6 cm), and the width can be different: 2.58; 3.05 cm, etc.
- The product goes on sale in packages of 16-22 pcs.
Varieties
In accordance with the number of trapezoidal rises in one element, soffit plastic panels come in the following types:
- two-lane;
- three-lane.
In addition, there are various models, each of which is used under certain operating conditions:
- Solid non-perforated– used for covering gable overhangs. In essence, this is a solid profiled panel with which the cornice is hemmed. The products perform only a decorative function and are convenient for finishing open structures - for example, the ceilings of garden gazebos.
- Partially perforated- These are panels with perforations in the center. When using such devices, effective ventilation of the under-roof space and interior spaces is ensured, as well as optimal removal of excess moisture, which prevents the development of mold. Soffits of this type can be used to cover any area of horizontal surfaces.
- Fully perforated used for protruding roofing parts: ridges, overhangs, canopies, cornices and others. This type of spotlight is convenient to use when constructing verandas, gazebos or porches. The use of a soffit with full perforation ensures free circulation of air masses and access of a large amount of air to the internal parts of the roofing pie.
The choice of plastic soffits must be treated very carefully, taking into account all the features of the building and operating conditions.
Features of plastic soffits
In modern construction, plastic panels are used very often. Such soffits become an excellent addition to the design of the house, especially if the facade is covered with vinyl siding.
The panels are presented in a wide range of colors, allowing you to select products of the required shade that will be in harmony with other decorative elements of the facade and roof. PVC panels are lightweight, durable, and easy to install.
A distinctive feature of cellular plastic panels is their large thickness: it can reach 8-10 mm. Therefore, in appearance, the products resemble wooden boards or panels, but they weigh significantly less due to the specific internal structure, made in the form of honeycombs (or cells), which is where their name comes from.
The width of honeycomb panels can range from 10 to 30 cm.
The advantage of wide models is the ability to carry out roofing work in a shorter period of time. The connection of honeycomb plastic panels is made using the tongue-and-groove method. Fasteners are placed in 30-centimeter increments.
Product advantages
Plastic soffits are a highly rigid plastic-based structure with excellent resistance to mechanical and atmospheric influences. In addition to the listed qualities, such spotlights have a number of other advantages:
- do not rot or corrode;
- do not collapse under the influence of ultraviolet irradiation;
- do not lose color intensity;
- universal: used for both exterior and interior decoration;
- thanks to its aesthetic appearance, they allow you to implement any design ideas;
- the use of such materials eliminates the need for additional work associated with painting them: plastic soffits are either pre-painted with ultra-resistant compounds, or due to their characteristics do not require an additional layer of paint;
- products are not susceptible to the development of fungus and do not contribute to the appearance of mold;
- caring for such a coating consists of simply wiping with a cloth or washing with plain water;
- when choosing the appropriate models, effective ventilation of the under-roof space and interior spaces is ensured.
Additional details
- The J-profile is needed for lateral connections of soffit panels to a variety of structures: door and window openings, cornices along the gables of the building. The soffits are fastened using a narrow J-profile.
- The frieze strip (J chamfer) is used when hemming the eaves of the roof. With the help of this part, the distance from the bottom of the roof sheathing to the coating drip line is closed. If this space remains open, then from the outside you can see the entire interior of the roofing pie: insulation, sheathing, under-roofing films.
- Finishing strip - the purpose of its use is to complete the installation of siding panels and additional accessories. Such strips are installed near the windshield, window trims and under the eaves. J chamfer can be installed without the use of a finishing strip only if curtain rod hooks are installed.
- The connecting H-profile is designed for turning soffits at corners or connecting siding panels. The cross-section of this part resembles the letter N. This element is used for installing siding in those parts where the length of the wall exceeds 8 meters.
- The external corner is designed for installation at the corners of the building. When finishing roofing or wall structures, this element is used as a turn. It can also be used as a window detail.
- The internal corner is mounted in the internal corners of the building. When finishing roofing or wall structures, it is used as a turn. In many cases it is used when installing soffits with siding.
Review of manufacturers
HOLZPLAST
Soffits from the German company Holzplast are among the highest quality products presented on the European market of finishing materials. They go well with all brands of siding, since they can be matched to the color of the siding, as well as the color of the roofing and gutters. Thanks to the use of Holzplast soffits, the exterior of the house will acquire a harmonious and finished look, and the roof and under-roof space will be reliably protected from the development of fungus.
The concern produces products that are unique in their properties. In 2009 Holzplast was awarded for its excellent product quality. Despite the excellent characteristics, soffits from a German company can be purchased by paying a very reasonable price.
Vinyl-based siding is produced using a co-extrusion method, which ensures the creation of two-layer monolithic elements. The plastic is forced under high pressure through soffit-shaped holes. After the plastic tape comes out of the mold, it is cut. Then the material is given the working profile of the soffit. The latest German equipment is used in the production of spotlights.
MITTEN
Soffits from Mitten are the highest class finishing materials. They are presented in a wide range of colors. The paint is particularly resistant to fading.
14 colors of soffits make it easy to match them to the color of the siding or roofing.
Installation of products is not particularly difficult, but still requires certain skills. The manufacturer guarantees the high performance qualities of its products only if they are used for their intended purpose. Covering walls or ceilings with soffits virtually voids the warranty.
A distinctive feature of Mitten products is their reliability and durability, due to which they are in high demand throughout the world.
Soffits can be used in almost any climatic region, since they can withstand temperature changes ranging from minus 50 to plus 50 degrees.
The surface of the panels is matte, so they do not overheat even under the scorching rays of the sun, which often lead to deformation of lower-quality facing material.
Even at the production stage, all products are subjected to a series of tests and tests that confirm the compliance of Mitten spotlights with international quality standards.
The panels are easy to use, easy to clean, are highly resistant to damage and do not require the application of a protective layer of varnish.
Other advantages of Mitten spotlights:
- increased impact resistance: the material can withstand impact even in severe cold conditions;
- a wide selection of colors developed with the participation of psychologists: the shades never get boring and have a calming effect on the nervous system;
- products can withstand heavy rainfall and strong winds;
- unique color fastness of the material: depending on the specific series of the product, the color does not change from 25 to 50 years;
- no harmful additives, absolutely environmentally friendly;
- installation can be carried out even at temperatures of minus 20 degrees.
When purchasing original products, the Canadian manufacturer guarantees the preservation of the quality of the spotlights for 50 years
ALTA-PROFILE
Russian Alta-Profile soffits are one of the most economical options for these finishing materials, while their quality level is not inferior to their European counterparts.
A distinctive property of the products is their high color stability, due to which the panels retain their original appearance for a long time, regardless of the presence of negative environmental factors: heavy rainfall, intense ultraviolet radiation, etc.
The panels reliably protect the roofing pie and the under-roof space from excess moisture, prevent the penetration of insects, birds, rodents, debris, and leaves. All this extends the service life of roofing materials.
Soffits from Alta-Profil can be used for external cladding of gables and cornices of residential, commercial and household premises.
The production of panels is carried out on the basis of high-quality polyvinyl chloride resin and adaptives. Production is carried out on the latest equipment.
GRAND LINE
The use of Grand Line soffits allows you to create the perfect lining of the cornices. The optimal color choice goes well with chocolate and dark brown and the most popular roofing and façade colors. The additional elements presented in the assortment are made in brown and can be used when installing soffits.
Product Features:
Possibility of seamless installation. The specially designed geometry of plastic soffits allows you to create an invisible joint of panels when filing the cornice.
Fade resistance. The color stability of plastic products to ultraviolet irradiation has been confirmed by the results of a series of tests in the laboratories of Holland Colors, a leading European concern specializing in the production of dyes.
Flexibility and impact resistance. According to these indicators, Grand Line products are a recognized leader among Russian manufacturers. Thanks to these qualities, installation of spotlights can be carried out approximately 10 months a year, even at a temperature of minus 10 degrees.
Brown color stability. Plastic soffits retain the intensity of brown throughout their entire service life thanks to the use of paints whose quality meets European standards and a special production recipe.
The company warranty period for Grand Line plastic soffits is 50 years, during which the products are protected from any deformation (delamination, cracking, swelling).
For 9 years, the manufacturer guarantees color stability and preservation of its intensity.
Advantages of Grand Line soffits:
- reliably protected from rotting and corrosion;
- provide excellent ventilation;
- do not conduct electric current;
- fireproof (does not support combustion);
- easy to install and operate;
- easy to care for;
- resistant to physical deformation;
- environmentally friendly.
CONCLUSIONS:
- Today, plastic soffits are the most popular material for filing.
- Soffits are used for cladding downward horizontal surfaces: pediments, cornices, canopies.
- Plastic is flexible, easy to cut, and resistant to corrosion and rotting.
- Soffit plastic panels come in two-strip and three-strip; as well as solid non-perforated, partially perforated, completely perforated.
- PVC panels are lightweight, durable, and easy to install.
- A distinctive feature of cellular plastic panels is their significant thickness and cellular structure.
- When purchasing plastic soffits, you need to buy additional decorative elements.
- The Russian market offers products from both domestic and foreign manufacturers.
How to properly install spotlights from the Alta-Profile company, see the video.