The operation of this device is based on the principles of electrolysis and the splitting of water into ions. Containing negative ions is called catholyte or popularly “Living”, while those with positive ions are called anolyte or “Dead”. In order to separate both types between the electrodes, it is necessary to install an ion exchange partition.
It is believed that catholyte has an alkaline environment and has a positive biostimulating effect. It is mainly used in medical practice to treat various ulcers and wounds. Some gardeners use it to improve the growth of seedlings, some process vegetables and fruits by placing them in winter storage
Dead water is characterized by an acidic environment and has a sterilizing and disinfecting effect. It can be used to treat various skin diseases, and can also be used to disinfect premises and treat dishes.
Living water device diagram |
The device circuit can be easily and quickly assembled with your own hands. To do this, we need a diode bridge, steel electrodes and a piece of tarpaulin or its equivalent as a separating filter.
When the device is turned on, an alternating voltage passes through the diode bridge, is rectified and supplied to the electrodes, which are located in a jar of clean drinking liquid. Moreover, the positive electrode must be placed in a tarpaulin filter.
A tarpaulin filter can be easily sewn; it needs to be able to easily accommodate the electrode. It is best to use stainless steel for the manufacture of electrodes. But if you are going to drink the resulting liquid, use only food-grade stainless steel, but I would advise you to refrain from ingesting it. The average distance between the electrodes should be at least 4 cm, the sizes of the electrodes are arbitrary.
We turn on the device for 15 minutes or more, depending on what concentration we need the solution; before pouring the solution, do not forget to disconnect the device from the power supply to avoid electric shock. The solution from the tarpaulin filter must be immediately removed from the jar, otherwise it will mix and lose its properties. It is not worth storing the resulting solutions for a particularly long time; it is better to use them immediately, and if necessary, make more.
DIY silver water |
Since the times of Hyperborea, knowledge through troubled centuries about the healing properties of silver water and its bactericidal properties has reached our times. In the scientific works of the current cycle of civilization, scientists in the 19th century proved that silver has a disinfecting effect and is capable of destroying various microorganisms, including diphtheria bacillus and staphylococcal infections. Silver is an excellent bactericidal agent compared to copper and gold. This is true, because Ag ions can quickly penetrate into the cells of the human body, and they do not lose their viability.
There are two electrodes in a container with liquid, and there is a tarpaulin partition between them. When high DC voltage is applied to the plates, electrolysis occurs in the vessel.
The high voltage source is a step-up transformer with windings of 250, 500 and 750 V, designed for a current of up to 0.6 A. The rectifier is assembled using a bridge circuit using eight D246A power diodes. Resistors are connected in parallel to them to equalize reverse voltage surges. Diode V9 reduces current ripple in the electrode circuit. The electrolysis mode is monitored using an ammeter PA1 M2001 at 3 A and a voltmeter PV1 M2001 at 600 V. Toggle switch S1 sets the voltage on the electrodes, and a 6.3 V lamp is an indicator that the living water device is turned on.
Living water circuit diagrams of the device
They have been known since ancient times, but earlier, instead of neat purchased devices, they were made with their own hands. Following historical facts, devices for preparing dead and living water were available back in the 70s. To create two types of water, this device is required: “living” and “dead”. If you look at the publications of the magazines that our grandmothers subscribed to, you will definitely find a diagram of the device. The water activator was made independently because there was a shortage of goods all over the world, and especially of various kinds of devices and equipment. Let's figure out what the device consists of and how it works with living and dead water. Analogs exist only as professional equipment.
Design and how a DIY water activator works
A do-it-yourself activator processes water by applying direct current to it. Take a special container into which the electrodes will be immersed. In order to do this, you need to understand the operating principle of the device. Dead water collects where the anode electrode is installed. Dead water is separated from living water using a semi-permeable glass; it can be made from a piece of whatman paper, tarpaulin or any other suitable material. The activator receives a voltage of 220 volts from the network. The voltage is rectified and applied to the electrodes.
The conversion occurs due to the formation of a diode bridge. The cathode does its work from the lamp, which becomes a signaling device in the device system and a fuse for the electrode. You can learn about the preparation of living water by the dimming light bulb. If you exclude the incandescent lamp with a parallel switch, the procedure will speed up.
Ready-to-drink water not only becomes alive, its level of alkalis and acids changes significantly, and it can be determined using the pH value. Where the cathode is, the acidity does not exceed 9-10 units, where the anode is less than three. Determine values using special devices or chemical tests.
Stay safe
What is described above is a DIY design to activate water. In any case, there are some points where there are limitations and close attention is required:
—when you start making a device for living water, remember that the device is not safe for human health, since it runs on household electricity;
- the device can only be turned on with liquid; operation of electrodes not covered with water can lead to a fire;
— during the working operation, the walls of the vessel must not be allowed to come into contact with the electrodes;
— the electrodes can only be removed when the mains voltage is turned off;
— do not allow children close to the activator; if you are not present in the room, it is better not to connect it to operation.
Inventors of homemade activators suggest using powerful diodes and high current, calculated from 5A. Processes will go faster and security will increase. When a strong current passes through water, it can not only accomplish its intended purpose, but also heat the water so much that it boils. However, you should not think that at low values, for example at 0.1-0.5 A, the desired result is not achieved. The process that occurs at this moment is called electrolysis, and it can destroy the electrode. That is why professionals who have already gone through a lot and completed more than one device advise using only food-grade steel. Food grade steel has a low magnetic background, so it is ideal in this case. Ordinary stainless steel quickly decomposes, so it is absolutely not suitable in this case. To make an anode, it is recommended to take a high-class and clean schedule.
If there is a huge amount of impurities in the water, then the processing process will be several times lower. If you take it, then it is, of course, chlorinated and should sit for 3-4 hours. To remove iron, run through filters.
Functional homemade devices
If you don’t yet know about the beneficial properties of the activator, then read how many benefits they provide for health, help in caring for indoor plants, both living and dead water are present everywhere. The beneficial properties and healing properties of water are obtained by enriching water with ions. Various alloys use additives that prevent corrosion on the metal surface and create strength and aesthetics. prevents bismuth, molybdenum and other substances from entering the liquid. Some liquids can cause allergies. If substances accumulate in the body, they become a health hazard and can lead to cancer.
To avoid concerns, it is better to use a magnetic activator that is manufactured in production. Modern technology contains electrodes made of non-magnetic food steel in its devices. A magnetic activator separates liquids using a ceramic bowl. Manufacturers are responsible for the operation, safety and service life of this type of device. It is best to exclude negativity.
You can often hear the concept of a “magnetic” activator. This is a device that can change the level of calcium and magnesium salts; when heated, scale appears. In industrial production, there is an equally important device - a converter. The magnetic activator operates at high frequencies and has a generator.
The technique of making the devices is complex and difficulties will certainly arise when copying.
If you decide to make a magnetic activator yourself, you will need to prepare:
— purchase special programs or electronic circuits;
— in order for the operation to last as long as possible, high-quality structural elements are needed that do not have to be taken out for maintenance and will not need to be adjusted;
— diagnostics and even your own laboratory or special equipment;
— have experience working with electronics and understanding complex developments.
Even if you don’t make a magnetic activator, you can always do the simplest one outlined above. An activator for the home is as necessary as air, especially in our modern world, where water is far from being of ideal quality. The magnetic field will prevent scale from forming. Designs for the production of activated water are presented for informational purposes only. Everyone makes an activator device for themselves and is fully responsible for the safety of their home, health and life when working with a “homemade product”.
After completing work with the devices, you should rinse all elements, especially those where there was dead water. Living water can easily deal with greasy stains, while dead water has a bactericidal effect and can replace peroxide, especially when a large amount of liquid is required. After handling, wash your hands thoroughly to remove negative energy. If your budget does not allow you to buy an activator, then homemade work is simply the ideal option for you. The choice is yours, but remember that activated water is simply necessary for normal life.
Many of us have heard about the so-called living and dead water. This is discussed in books, this issue is touched upon in cinema, and finally, you can find information about such water on the World Wide Web.
And this is not fiction, living and dead water really exists. Let's talk about this in more detail.
Dead water (anolyte) is a solution obtained as a result of electrolysis, which has a large positive charge and a strongly acidic acid-base balance. Anolyte is known for the following properties:
- disinfectants;
- anti-inflammatory;
- antimycotic (antifungal);
- antiallergic.
Why does anolyte have such healing properties? There are no miracles here, everything is quite natural and can be explained from a scientific point of view.
The fact is that during the electrolysis process, chlorine and oxygen radicals and hydrogen peroxide are concentrated in the anode zone.
But they are the ones who help macrophages (the protective cells of our body) destroy the viruses, microbes, and fungi that come across them.
That's why contact of anolyte with a microbial cell leads to destruction of the microbial cell wall, leakage of cell components into the intercellular space, disruption of the functions of the ribosomal apparatus (it is responsible for the biosynthesis of protein from amino acids), and other unfavorable changes.
Living and dead water is certainly beneficial for the body, but so that it does not develop from a means of treatment into the category of “mutilation”, you need to know that:
- between the intake of dead and living water there must be at least two hours;
- When using living water not in combination with dead water, a feeling of thirst may occur. There is no need to suffer: drink acidified tea or compote;
- Living water quickly loses its properties, since it is an unstable active system. At storing living water in a cool, dark place it can be used throughout two days, and then a new alkaline solution (catholyte) should be prepared;
- dead water can retain its properties for 2 weeks if stored in a closed container;
- both dead and living can be used not only as a means of treatment, but also as a way to prevent diseases of the body.
But how do you get living and dead water?
Apparatus AP-1 ^
This device has a fairly high level of quality; it is a so-called electroactivator. In its manufacture the following were used:
- food grade plastic;
- electrodes made of ultra-strong noble metals;
- A ceramic glass made from a special type of clay.
Positive features of the product are the following points:
- The device looks very nice in appearance;
- it allows you to get almost one and a half liters of water in just 20-30 minutes;
- the device is characterized by low power consumption - at the level of a 40-watt light bulb;
- The anodes of the device are made of titanium and coated with a platinum group metal, the cathodes are made of stainless steel.
But it should be noted that AP-1 costs significantly more than other devices. So, for a model with an indicator reflecting water quality, you will have to pay about 100 US dollars.
"PTV" ^
This device differs significantly from the previous three, since it is intended primarily for professional activities (sanatoriums, rest homes, medical institutions), although it is also used at home.
The main advantages of the device are:
- low power consumption for a product of this class – 75 watts;
- thick electrodes;
- long service life.
Besides, This device does not have a glass in which dead water is prepared. Instead, there are simply two separate containers separated by a special wood membrane.
But still, the disadvantage of this device is its cost. For home use device 130-140 dollars- already too much.
Are you concerned about your health and the condition of your back? Then be sure to read the article about how healthy they are, how much they cost, and how to make the right choice?
In the summer (and generally in the warm) season, it is very useful to swim in the fresh air. Summer shower cabins installed in the country can help you with this. Read all the most important and up-to-date information: prices, selection and installation features!
A very beneficial activity for health (including weight loss) is water aerobics. Read more about this sport in the article:
, it is very interesting!Making living and dead water with your own hands ^
In addition to the officially manufactured devices discussed above, there are also homemade ones. We will offer one proven method for making water yourself. So, for this you will need:
- two stainless steel mugs;
- several syringes;
- ordinary wire - a cord with a plug at the end;
- one diode.
It is better to purchase mugs with handles, since you need to drill a hole directly in the handle and screw a diode into it (you should use diodes with a load of 220 volts, 6-amp).
The mugs themselves should be mounted on a stand made of non-conducting material. To strengthen it, you can cut holes in the stand that are equal in diameter to the bottom of the mugs, or you can simply glue the mugs.
Two syringes are glued together into a single U-shaped tube (to do this you will have to cut their tops), and another syringe is firmly inserted on top (directly into the middle of the crossbar of the imaginary letter “P”).
When the homemade device is ready, the mugs need to be filled with water and placed on a stand.
The prepared tube should be lowered into the circles so that one end of the letter “P” is in the left circle, and the other in the right.
After this, the upper syringe is pulled out all the way (thereby filling the tube with water). Then the end of the wire with a positive charge is connected to the diode (remember, it is installed in the handle of one of the mugs), and the end of the wire with a “minus” is connected to the other mug.
The plug is plugged into the outlet and left overnight. By morning, this unique device will produce dead water (in the mug where the diode is installed) and live water.
How to make water in the device? Instructions for use ^
Of course, not everyone will decide to create a device for preparing living and dead water on their own, and therefore you need to know how to work with the purchased device.
So, most devices have a container for living water and a separate glass for dead water (as we have seen, the glass can be fabric or ceramic).
Initially, the container is filled with water, and then the device turns on.
After this, the process of polarization of solutions begins and standard electroosmosis clearly occurs: the liquid flows towards the negative charge (accordingly, the anolyte level drops).
As soon as the redox indicators of the catholyte and anolyte are equalized, the water will flow in the opposite direction due to repolarization.
In this interesting way, factory-made devices provide the production of living and dead water.
What do people say? Reviews about the use of living and dead water ^
All descriptions, of course, are good, but you always want to learn about the use of devices and the water itself from ordinary people. Having collected all the information from the reviews, we offer some of the most common points:
1) making a device yourself is quite unsafe, since there is a high risk of water contamination due to the materials from which this device will be created;
2) the cheapest devices do not achieve the intended effect, and therefore their purchase is a waste of money;
3) water can be used to heal wounds. First, the wound is treated with dead water, and after drying, with live water.
Many people say that after they started using living and dead water, they completely forgot about pills and doctors:
“My kids always had runny noses, all year round. And then I decided to use living and dead water. And now for 4 months my children have not been sick at all!”
“My wife suffered from problems with her pancreas. I started drinking water and that’s it! Now she doesn’t have any pain at all, and she doesn’t need diets at all.”
“I started drinking this water just out of curiosity. Now I’m always in a good mood, and I work with such zeal that all my friends are jealous.”
Well, let the treatment with living and dead water benefit you too. Be healthy!
Video about the health benefits of living and dead water:
No related posts
35 reviews per article“ Treatment with living and dead water: fairy tales or reality?”
Alex11
Healing with water is interesting. But the names are living and dead water, of course, you immediately remember fairy tales. And accordingly, such names do not add trust. Although the idea itself is interesting.
- Paul
I have been using the Iva-1 water activator for 2 years now, before that I used the Ap-1 activator. To be honest, Ap-1 is an activator that is not worth the money. The anode is not coated with platinum, but with Teflonium material. And this material is subject to anodic dissolution: (I found out that 1 anode electrode costs about 900-1000 rubles. And they sell this AP in bulk for 1500 rubles. Therefore, they saved on the material.
Now I’m using Iva-1 activator, there’s a really good coating (I submitted it for examination) - it’s really a sputtering of ruthenium (this is a platinum group metal), so it just doesn’t dissolve during electrolysis. In general, it corresponds to its price - 4100 rubles. And about water, believe it or not, it really heals!!!- Elena
It’s true, my grandmother used homemade medicine to heal tragic wounds.
- Sergey
I made electrodes from silver. I took two silver fifty rubles. One cathode and the other anode, or vice versa, depending on where the + or - of the power source is
- Yuri
Two fifty kopecks of what standard? To make a good silver electrode you need 999 standard - the highest, the standard means how many grams of silver are per 1000 grams. Your fifty dollars are most likely 925 standard - this means that along with silver there are also impurities of other metals and when you supply electric current to such an electrode, on the contrary, you will make the water even worse. I advise you to buy a water silverer, there are many of them on our market, for example, IVA-2 Silver, this installation already has an electrode with 999 fineness. Otherwise it's up to you :)
- Marina
To be honest, the phrase “dead water” sounds somehow strange and even repulsive, but in fact it is very useful, no less than the so-called “living water”. Having learned that the properties of water can be changed, I bought a special device and began to use water for medicinal purposes. The result was amazing: I began to feel much better, the headaches went away.
- Anatol
- Albert
I watched a TV program about the unusual properties of water. It turns out that water has the ability to change its crystals depending on its surroundings. Scientists took a drop of water and played a recording of some classical music or children's laughter next to it, and the water crystals took on various beautiful shapes in the form of snowflakes, etc. They did the same thing with another drop, only the recording was different, for example, hard rock or swear words. In this case, the water crystals disintegrated into “torn” pieces or took on ugly shapes. Like this…
- Julia
I read an article by a doctor of chemical sciences about ionized water, “Arguments in favor of alkaline water. Letter to the editor from a doctor of chemical sciences." I recommend it to everyone http://www.labprice.ua/naukovo_pro_chudesni_vlastivosti_vodi/argumenti_na_korist_luzhnoi_vodi_list_v_redakciyu_vid_doktora_ximichnix_nauk
- Holgina
The idea of dead and living water is interesting, but I don’t want to experiment on myself. It's kind of scary.
- Andrey
I don't trust such inventions. I prefer to drink regular filtered water.
- Komzin Boris
Our water cannot be used for treatment at all; it can only harm health if taken for a long time.
- Alexander
I tried it on myself back in 1985-95. The device was homemade. The pH was checked with ordinary litmus paper. Very effective remedy!!! I made the device and started using it, because I tried a lot of remedies for radiculitis, all kinds of ointments, massage, cast iron, copper shavings... nothing helped. Using J. and M. water, the pain went away in just a few (2-3) days. Until today, the pain has not recurred. Sore throat is treated within 2-3 rinses, after an hour. Yes, many diseases are easily treated. In addition, the effect of using water is long-lasting. And also, as far as I understand from experience, water is not purified, but decomposed into its component parts. To obtain the F and M components, it is better to use already purified water. Both derivatives are useful! So I recommend it to everyone!
- platonii
And what does the truth cure?
- Daniel
I make living dead water using the IVA 2 device. I mainly use living water, catholyte, for half a year. I noticed a weakening of the symptoms of vegetative-vascular dystonia. I began to do without many vasodilator medications. I feel better. Living water is certainly not a panacea, but it significantly alleviates painful conditions. It also has a tonic effect.
For a long time, there have been legends about “living” and “dead” water. This is no coincidence - life on Earth is impossible without water at all; humans are 80% water. Its condition and human health as a whole depend on what kind of water our body consumes. There are more paradoxes associated with water than there are reliable physical interpretations. Take, for example, Epiphany water. It does not deteriorate for many months, even if collected from a water tap or a “dirty” source. Some scientists associate this fact with a decrease in the electrical conductivity of water during the period of least solar activity and, as a consequence, a decrease in the growth of microorganisms. This is the so-called “dead” water effect.
On the contrary, “live” or activated water helps strengthen the body’s immunity; there is confirmed evidence of the positive effect of its use in the treatment of certain diseases (infectious diseases, diseases of the digestive system, arthrosis and many others). Of course, unable to give a truly scientific explanation for the physical and biological processes occurring in water, many scientists completely reject both the beneficial and negative effects of living and dead water. This fact, however, does not in any way affect the amazing properties of water.
Schematic diagram of a device for obtaining living water
In order to obtain dead and living water in the simplest way, you can assemble a basic electrochemical device according to Scheme 1:
The device is supplied with an alternating voltage of 220 volts from household electrical wiring, so precautions must be taken: carefully insulate live wires, do not come into contact with water and circuit elements during operation of the device, and provide a safety system. It is better to turn on the device through an extension cord with a built-in switch and an industrial fuse. The anode (positive electrode) and cathode (negative) can be made of chemically neutral stainless steel or food-grade aluminum (the material from which cans for drinks and beer are made). The electrodes are carefully secured to the plastic cover using a fiberglass or other elastic non-conductive gasket and a screw connection. The circuit includes a semiconductor diode for rectifying alternating voltage. It must be designed for a forward current of 5 Amperes and a reverse voltage of over 300 Volts. Among domestic elements, diodes D231, D232 are suitable.
Components of the device
The lid is placed on a glass jar of the appropriate volume into which water is filled. To separate living and dead water, use a canvas hose or other dense fabric bag surrounding the positive anode, as shown in Figure 2:
According to the electrochemical theory, during the electrolysis process, a highly acidic composition (anolyte), called “dead” water, is formed around the positive electrode. It has antiseptic, antibacterial, antiallergic and many other properties that are not always useful. All remaining liquid inside the vessel is an alkaline solution (catholyte) of varying pH levels (from 2.0 to 10.0) depending on the initial amount of salt impurities in the water and the production technology. This is what is called “living water.” The optimal time required for preparing dead and living water is approximately ten minutes, storage duration is no more than three days.
The appearance of homemade devices is shown in photographs 3:
In the second device, instead of a half-wave rectifier on one diode, a full-wave rectifier bridge on four diodes is used. This circuit solution allows you to increase the performance of the device. For a more convenient separation of dead and living water, you can make a device consisting of two separate containers, as shown in Diagram 4:
According to this scheme, the electrochemical process is maintained by current passing through a wetted linen or cotton cord. In this case, living and dead water will be accumulated in separate vessels, which is very technologically advanced. The features of the proposed circuit include a lamp connected in series, designed to simultaneously limit the maximum current and indicate. At the beginning of the process, the lamp burns with the greatest intensity; as the process progresses, the brightness decreases.
Industrial design of the device
Industrially produced electric water activators are now available for sale. Photo 5 shows the appearance and composition of the Espero-1 device:
The principle of its operation is similar to the devices described above; the properties of the water produced by this device, in principle, should coincide with homemade living and dead water.
The paradox is that in addition to purely physical and chemical properties, water has such incredible properties as energy and information. It is known and proven that water can be charged with human thought; the same water can have both positive and negative effects on the human body. Water, being at the same time an indispensable condition for human life, is the main cause of his diseases. As for the variety of states of water, liquid water has five states, frozen water has fourteen. It has the highest heat capacity of all liquids and transfers heat from southern to northern latitudes, determining the climate on our planet. Having made a homemade device, you can independently continue to study the incomprehensible properties of the basis of life on Earth, water.
Dear readers, comment on the article, ask questions, subscribe to new publications - we are interested in your opinion :)
Every person dreams of a long and happy life, which is not overshadowed by various ailments. And traditional medicine has always sought to fulfill this desire. She has accumulated vast experience in the study of medicinal plants and has created many recipes that relieve various diseases.
One of the miracle cures offered by traditional medicine is water, which is called living and dead. Do you remember how in fairy tales, when they used this method to resurrect a dead hero? First he was sprinkled with dead and then living water.
History of application
The gifts of nature have long been used by humans for medicinal purposes. One of them, which deserves special attention, is “life-giving water.” Even in ancient manuscripts, researchers found a mention that during his military campaigns along the mountain ranges of the Pamirs, Caucasus and Tien Shan, Alexander the Great found a source of healing water. He collected the liquid into a jug, but his daughter stole it and poured it on herself. As a result of this, she became invisible and immortal.
There is also information that many Popes, Chinese emperors and other powerful people organized expeditions in search of an elixir that would allow them to obtain immortality. All these fairy tales and legends are clear confirmation that our ancestors knew about the existence of living and dead water.
Sources
Today you can make living and dead water with your own hands. And in ancient times, people took it from natural sources.
The dead one was in stagnant lakes and swamps. This liquid was not consumed internally. It was used only by healers for various external potions. The water of mountain rivers, glaciers and waterfalls is considered alive. It was drunk and also used in the preparation of various medicines.
Modern research
Today, to obtain healing liquid there is no need to search for its sources. To do this, it is enough to make a living and dead water apparatus at home. When used as a result of hydrolysis, so-called activated water is obtained.
Soviet scientists were busy studying the properties of this liquid back in the 80s of the 20th century. However, the results of all experiments and experiments were simply kept secret for the general public. However, everything secret sooner or later becomes clear. After some time, doctors and traditional healers learned about the results of the experiments. And here the work of Western researchers played a big role. Their results could be read in published scientific articles.
Research has proven that living water, also called catholyte, becomes negatively charged due to hydrolysis. This transformation helps it obtain high regenerating and immunostimulating properties. This makes it possible for a liquid that has undergone the hydrolysis process to become healing and be used to get rid of many ailments.
The unique properties of such water were confirmed by the USSR Pharmacological Committee. At the same time, it was said about its absolute harmlessness not only for external, but also for internal use.
The water that accumulates near the positive electrode after electrolysis is called anolyte. Its unique properties have been known to traditional healers since time immemorial. Thanks to this water, people managed to escape from rotting wounds and bedsores.
Obtaining healing liquid
In order to get activated water, you do not need to look for some distant and sometimes inaccessible sources. To do this, just open the tap and use a special device.
Based on the basic concepts of chemistry, living water has alkaline properties. They contribute to the healing effect. The properties of dead water are acidic. That is why it exhibits a disinfecting effect.
Electric current, when passing through ordinary water, radically changes its internal structure. At the same time, it erases harmful environmental information contained in the liquid. After such treatment, the water is divided into living and dead. Moreover, each of these two fractions has medicinal qualities.
Experiments on the use of activated liquid
The first apparatus of living and dead water in our country was invented by N. M. Kratov. The idea of creating this device did not come to the author by chance. In 1981, Kratov was treated in hospital. There he was diagnosed with prostate adenoma. Simultaneously with this pathology, he suffered from an inflammatory process in the kidneys. The course of treatment in the hospital lasted for a month, but did not bring any tangible results. That is why doctors offered Kratov surgery. He refused surgery and was discharged home.
At the same time, Kratov’s son suffered from a long-term non-healing wound. And the author, who created the apparatus of living and dead water, began to test the properties of the healing liquid on the affected area on his son’s skin. The results were not long in coming. The wound healed within two days. Such success inspired the inventor. He began to take this water himself, and soon his health improved. Along with the adenoma, radiculitis and leg swelling went away.
Application area
In addition to Kratov, the healing properties of such water were studied by G.D. Lysenko, as well as a number of other authors. As a result of the research, it became obvious that water, both living and dead, can save a person from almost fifty types of various diseases, starting with tonsillitis and ending with stomach and duodenal ulcers.
This list also includes such common diseases as colds and flu, runny nose and radiculitis, hypertension, etc.
Making at home
In order to use the healing liquid, it is enough to make a device of living and dead water with your own hands. Of course, such devices are not difficult to find on sale. Buying and delivering them will not be difficult.
However, the purchased apparatus for obtaining living and dead water, when examined in detail, has a rather simple design. This makes you think about saving money. After all, the price of such a device is not so low. It is much easier to make a living and dead water apparatus with your own hands. It will only require a little time and a small amount of materials. The skill of our masters is always present.
Main details
In order to build a living and dead water apparatus with your own hands, you will need:
Glass jar;
- diode bridge that rectifies the mains voltage;
- a bag made of waterproof fabric;
- two electrodes;
- power cord.
With the help of skillful hands, all these parts can easily turn into a homemade apparatus of living and dead water.
Electrodes
This part must be made of food grade stainless steel. Salad bowls left in the house from Soviet times are perfect for this role. But if they are not there, then any utensils made from stainless steel will do. A graphite rod can be used for the anode.
If the apparatus for preparing living and dead water is assembled using a half-liter jar, then the length of the electrodes should be 100 mm. However, this volume can be increased. In order to create a device for living and dead water with your own hands, you can take a three-liter jar. In any case, the electrodes can be extended. Their size should be such that the distance between the metal and the bottom of the glass container is at least 5-10 mm.
Stainless steel sheets suitable for the manufacture of the anode and cathode should be 0.8-1 mm thick. Some craftsmen claim that they created the apparatus for making living and dead water using aluminum electrodes.
Pouch
This part will be needed to separate the resulting water fractions. As a rule, a tarpaulin is used to make a bag. This could be a piece from a fire hose or a gas mask bag. But in any case, the material for the bag should not contain any impregnation. In order to ensure that there are no foreign substances, the prepared piece must be placed in water and boiled. The components used in impregnation will manifest themselves when heated.
The length of the finished bag must be in full accordance with the height of the glass jar used to create the apparatus. When cutting this part, cut off the required length of the tarpaulin. The bottom of the bag is sewn up with a piece of the same material or food-grade plastic is inserted.
Device assembly
The diagram of the apparatus that receives living and dead water is quite simple, and you can familiarize yourself with it in the article. To assemble the device, a U-shaped cut is made on the positive electrode. It is necessary to place a cloth bag on the anode. It will collect dead water. There is no need to make such a cut on the cathode.
Both electrodes are attached to the jar using an ordinary nylon lid. However, here it is worth using one trick. Due to the fact that such covers have little mechanical strength, it is best to attach the electrodes to them using an insulating sealing gasket. This will avoid unpredictability of their behavior during work. Such gaskets are made of fiberglass (without foil) or any plastic. This part has the appearance of a rectangle with rounded ends. Two holes are cut out on it, the diameter of which coincides with the diameter of the electrodes. The gasket is installed on the plastic cover. During operation, when living water and dead water are formed, the device releases gases from the liquid. For their exit, an additional hole is provided in the lid.
Next, a rectifying diode bridge is attached to the electrodes. It is important to mark the positive and negative outputs to the plate (“+” and “-”). For safety reasons, the bridge can be covered with a lid. When using a threaded diode, the thread must be attached to the positive electrode.
There is another way to assemble a similar circuit. It can be performed with a rectifier bridge. In this case, living and dead water will be produced even more intensively. The device (reviews from craftsmen confirm this) will become four times more powerful. Accelerating the process of preparing healing liquid is especially important when using it systematically.
A power cord with a plug is connected to the diode bridge. Its length must be at least 500-700 mm. At the same time, it is important to insulate all open electrical connections, because for the process that results in living water and dead water, the device consumes an alternating voltage of 220 V. Next, the electrode, which is marked with a minus sign, is placed in a tarpaulin bag and poured into a jar water, and the entire structure begins to work when connected to the electrical network.
Preparing water
Getting the healing liquid is quite simple. To do this, pour water into a cloth bag. Next, a positive electrode is placed in it. This entire structure is immersed in a jar of water. And here there are also some nuances. The water in the jar should not be filled to the brim. It should be slightly below the top edge of the bag.
The whole process lasts no more than 5-10 minutes. Next, the electrodes are removed from the jar. This must be done very carefully. Otherwise, a mixture of the two resulting fractions will occur. At the end of the process, the water from the cloth bag is poured into a separate bowl.
Assembling a device with a different design
Due to the need for careful handling of the resulting fractions, this device is not very convenient. In addition, certain safety precautions must be observed when the live and dead water apparatus is operating.
The instructions for it warn that all manipulations of pouring water and removing the final product must be done without plugging the device into a power outlet.
A device whose design does not include the use of a fabric bag is considered more convenient. In this case, you will need to take two containers. However, banks are not suitable for this. Such containers are distinguished by the absence of a neck and steep, straight edges. The design of the electrodes in such a device remains unchanged. The only difference between such a device is that the anode and cathode must be installed in separate containers. Electrical contact must be ensured between the electrodes. To do this, they are connected with a cotton band wrapped in gauze, which is pre-soaked in water. Such a part will allow ions to move freely. As a result of the operation of the device, both living and dead water will be produced. Moreover, each of them can be seen in a separate container. This allows you to simply disconnect the installation from the network at the end of the work and obtain anolyte and catholyte immediately, and in equal volumes.
In the scheme of this design, as in the previous version, it is advisable to use a light bulb with a power of 15 W. They are usually used in sewing machines and refrigerators. If the electrodes are short-circuited, the light bulb will play the role of a fuse, and if the process does not have any failures, it will act as an indicator. At the beginning of water production, the light from it will be quite bright. Towards the end of the process, the light will begin to dim. The signal about the end of the production of activated water will be its complete shutdown.
Rules for using healing water
The catholyte prepared in the device is an alkaline solution with a bluish tint. It is a clear, soft liquid with an alkaline taste with a pH of 8.5 to 10.5. Catholyte, or living water, is able to retain its healing properties for at least two days. Only in this case it is important that the storage conditions are met. Living water should be kept in a closed container and in a darkened room.
The analyte has a yellowish tint. In addition, the difference between dead water and living water lies in its astringent, sour taste and somewhat acidic aroma. Anolyte retains its properties for half a month. But this only happens when it is stored in a closed container. The acidity of such a liquid is from 2.5 to 3.5 pH.
Activated water should be heated before use. However, some caution must be exercised. Water should be poured into a ceramic or enamel bowl and heated over low heat. Using an electric stove will cause a loss of its beneficial properties. It is strictly forbidden to bring such water to a boil. In this case it also becomes useless.
If both dead and living water are used at the same time, then between their doses you need to take a break of at least one and a half hours. In the case of local application, the pause is much shorter. It is only 10 minutes. This dosage regimen can be explained by the fact that when the analyte and catholyte are mixed, they are neutralized. As a result, the healing liquid simply loses its activity.