How to set a timer on a Sherkhan 7 alarm system. Limiting the number of autostarts by timer

The system developers offer a comprehensive solution for the security function for a car, which takes into account modern requirements for reliability and ergonomics. The device consists of several components, including two-way communication with the owner, engine and transmission control. At the same time, SCHER-KHAN MAGICAR 7 belongs, if not to budget security equipment, then to the middle segment, at least. Despite its widespread use, the complex does not have the characteristics of typical premium complexes. But in its niche, of course, the system demonstrates an example of the implementation of a well-assembled, technologically advanced and easy-to-use device.

Alarm Features

The system is formed by a set of components designed to safely control access to the vehicle. A combined engine control scheme via remote electronic means was used. The equipment set includes a central control unit, a set of cables, key fobs, a siren and sensors. The main control unit is a processor that receives and processes signals from key fobs, sensors and other devices included in the security infrastructure. For example, the SCHER-KHAN MAGICAR 7 alarm system includes shock sensors. This means that if you try to break the windshield, the controller will detect a break-in attempt and sound an alarm signal to the siren. The connection between the processor and key fobs works in a different functional direction. A signal from the driver approaching the car through the controller activates the engine at the moment the corresponding command is received. The system is powered by a 12 V on-board network. The above-mentioned supplied wires are used to organize the power supply.

Instructions for managing key fobs

The key fob must initially be prepared for operation as a communication device. That is, it must always be ready to interact with the remote devices of the MAGICAR 7 SCHER-KHAN alarm system connected to it. The instructions recommend that before working with the key fob, check the reliability of its battery supply, and then become familiar with the controls. User interaction with the system through this gadget mainly occurs through indicators. Among them are indicators of communication between the device and the central unit, signal level, battery charge indicator, characteristics of the microclimate in the car, engine operating parameters, etc.

As for the controls themselves, the key fob is equipped with a set of buttons that can be used in combination. The developers did not provide a clear correspondence of specific keys to the functions of SCHER-KHAN MAGICAR 7. The key fob can be customized according to individual preferences in terms of the optimal control configuration. For example, through the programming mode, each button can be assigned a specific command.

Instructions for arming

Activation of the armed mode can be done by pressing one key fob button, which, again, is programmed in advance. Before setting the security mode, the car must be completely locked so that the mechanics of the locks do not conflict with the electronics of the MAGICAR 7 SCHER-KHAN. The instructions also indicate that full protection is realized only if sensors are connected. That is, through the same key fob, the mode for activating the ignition detectors and calling the car owner is set.

Arming is possible even when the engine is running. To do this, you need to close the doors with windows, trunk and hood, but leave the ignition on. Next, the tachometer format of the SCHER-KHAN MAGICAR 7 complex will come into effect, which is also programmed in advance. In this case, the power unit will not just work in a locked car, but will adhere to certain parameters. This option may be required, for example, for heating.

Engine start control

Remote engine start is one of the key functions of alarm systems of this type. By default, the engine starts by pressing the second key fob button, held for 2 seconds. But it is the engine that is activated, and the locking mechanisms will remain in the security mode. The user can also configure the automatic start of the power plant through the SCHER-KHAN MAGICAR 7 system. Auto start is implemented with the parking brake set, the ignition off and the hood locked. If we are talking about a car model with a manual gearbox, then you need to initially configure the operation of the complex to enable start reservation.

The Sherkhan Magikar 7 car security system is justifiably popular among car owners due to its simplicity and reliability, although its price fully corresponds to its declared qualities.

How to remotely start and turn off a car (from the key fob)

Starting the engine from the key fob

To start the engine, you need to press button 2 on the main key fob of the Scher Khan Magicar 7 and hold it for 2 seconds or a little more. The security mode is activated and the engine starts. At the same time, a countdown will appear on the display of the key fob communicator, showing how much time the engine has left to run before automatic shutdown. Therefore, you first need to set the desired engine operating interval (5, 15, 25 or 45 minutes).

When starting the engine from the key fob:

• The siren will sound;
• The emergency light will go off once;
• The LED indicator will blink;
• A short signal will sound from the main key fob.

If the car has a manual transmission, and it is not set to the handbrake, then it will not be possible to start the car with the key fob - this should be taken into account in advance by owners of cars with a manual transmission.

After the first unsuccessful attempt to remotely start the engine, the system will make 2 more attempts to start. If they also fail. then you need to contact the technical station. service.

Stopping the engine from the key fob

To turn off the engine, you need to press button 2 on the main key fob and hold it for 2 seconds or a little more. As soon as the engine is turned off, the shock sensor is activated after 30 s.

The following signs indicate a successful remote engine stop:

• The siren will sound twice;
• The emergency lights will also go off twice;
• Several signals will sound from the main remote control.

How to set up autostart of Scher Khan Magicar 7 from the key fob based on temperature and time

Setting autostart based on temperature

The setup is as follows:

1. Activate start by timer 1-13.

2. Activate mode 1-21, which regulates the temperature (Roman buttons 2, 3 and 4).

3. Press button 4 and automatic start based on temperature will turn on. After this, the siren will sound 21 times.

4. Set the desired engine temperature at autostart (possible options are -15, -25, or +60°C):

• button 2 – if we want the machine to start at -15°C,
• button 3 – for autostart to occur at -25°C,
• button 4 – designed for autostart at t +60°C.

5. Exit the timer mode by simultaneously pressing buttons 2 and 4.

6. How long warm-up is required - this is set by buttons 1 and 2, and at the end of programming autostart by temperature, you need to press button 3, 12 times, then the warm-up time will increase..

Setting autorun by time

Here the setup looks like this:

1. Enter the command programming mode by simultaneously long pressing buttons 2 and 4;

2. Enter timed autostart mode: press and hold button 4 until the siren sounds 13 times;

3. Select the autorun interval, i.e. after how many hours autorun should resume:

• button 2 – after 8 hours,
• button 3 – after 4 hours,
• button 4 – after 2 hours.

4. Exit the timer mode by simultaneously pressing buttons 2 and 4.

How to disable autostart of Scher Khan Magicar 7

To return to factory settings:

• Turn off the car alarm and ignition. Activate the programming mode by simultaneously long pressing buttons 1 and 4 for at least 2 s.
• Press button 3 three times. The hazard lights will flash as confirmation, then the siren will sound 3 times. That's it - all your settings have been removed, now on Sherkhan Magikar 7 only the original factory settings.

Why doesn't autorun work? Troubleshooting

It happens that it is simply impossible to put the car on autostart. When you press and hold button 2, an open door and error 03 appear on the display. The door switch is probably in the way, therefore, repairs are required at a car service center.

Have you bought a scher khan magicar 7 alarm system, but don’t know how to use it? – you have come to the right place. Follow the link to download detailed operating instructions.

Scher khan magicar 7 is one of the best premium alarm systems with automatic start and two-way communication.

ATTENTION! A completely simple way to reduce fuel consumption has been found! Don't believe me? An auto mechanic with 15 years of experience also didn’t believe it until he tried it. And now he saves 35,000 rubles a year on gasoline!

The device is mainly notable for its communication range of 1500 m, which greatly distinguishes the alarm from other models.
Most people neglect to read the instruction manual. Some are lazy, while others are confident. Unfortunately, this is a huge mistake that leads to unpleasant consequences. For example, a person cannot unlock and start the car, or disable the security system.

No matter how well you know the device, be sure to take the time to read the information about Sherkhan 7. This way, your device will always work perfectly and will not cause any trouble.

What's in the installation instructions

• Purpose of the magicar 7 product (scope of delivery, technical specifications, areas of protection, list of functions, etc.).
• Description of key fobs (locking, description of modes and much more).
• System operation (arming, description of functions and modes, programming key fobs, etc.)

The instructions were created specifically for dummies. It describes in detail everything related to the alarm, down to pictures and step-by-step instructions. If you have little or no knowledge, thanks to a detailed description of the entire device, as well as the operating principle, you can easily install autostart, as well as set up a car alarm in a convenient way.

I am a novice car enthusiast. Can I install scher khan magicar 7 for myself?

After reading the instructions - definitely. The text is written in the simplest possible language. All unusual words have definitions. No wonder the book has more than 80 pages. This is one of the best instruction manuals, because it is not intended for professionals who understand mechanics, but for everyone.

The Magikar 7 car alarm is considered one of the most elite anti-theft systems with two-way communication and automatic engine start. The presented alarm system is equipped with the ability to connect to the CAN information bus for reading information and its further transmission. Although the alarm system was released relatively recently, it has already established itself as one of the most reliable and high-quality security systems. Using the Sherkhan Magikar 7 remote alarm key fob, it is possible to start the vehicle engine from a certain distance, and the alarm operates at a distance of about two thousand meters.

Today we will talk in more detail about the Sherkhan Magikar 7 car alarm.

First, let's look at the equipment of the Sherkhan Magikar 7 alarm system:

• Keychain and case for it;
• Main block;
• Siren;
• Shock sensor;
• Call sensor;
• Temperature sensor;
• Motion sensor;
• Installation kit;
• Installation and use instructions;
• Sticker on glass.

Now let's move on to the main features of the Sherkhan Magikar 7 alarm system:

1. Alarm clock with which you can set the time for automatic engine start;
2. Automatic and remote engine start;
3. Additional tachometer sensor;
4. Indication on the key fob;
5. Turbo timer equipped with intelligent mode;
6. Ability to block key fob keys;
7. Energy saving of the electronic battery of the key fob.

How to install an anti-theft system

Due to the use of Sherkhan Magikar 7 most modern solutions in the development of car alarms, the complexity of installing an anti-theft system on a particular vehicle is greatly simplified.

There is no need to search for a signal from any electrical devices throughout the vehicle, the number of connected wiring has been significantly reduced, and it is now possible to install a security system even in the most inaccessible places.

Although this car alarm is quite easy to install, you still need to comply with some requirements:

• Wiring for connecting the main unit must be laid exclusively in places intended for laying standard wiring;
• Before starting installation, carefully study the installation instructions;
• Do not place any alarm components in areas of high heat;
• Collect wires into bundles, or better yet, protect them with insulating tape;
• Under no circumstances bend the wires over the metal edges or pinch them with the upholstery panels;
• Mount the shock sensor only on a hard surface;
• Extend wires exclusively using an identical wire or a wire with a larger cross-section;
• When installing the trunk and hood opening sensor, the free play of the sensor rod should be about five millimeters.

The vehicle alarm system STSTS SCHER-KHAN MAGICAR 7 (hereinafter referred to as the system) meets the mandatory requirements in the GOST R certification system for security devices for vehicles :
GOST R 41.97-99 - Uniform regulations concerning the official approval of vehicle alarm systems
(STSTS) and motor vehicles in relation to their alarm systems (STS) GOST R 50009-2000 - Electromagnetic compatibility of technical equipment. Technical means of security alarm.

Requirements and test methods
Thank you for purchasing the SCHER-KHAN MAGICAR 7 two-way car security system. Our company's constant research and development implements the most advanced ideas and serves to satisfy all the needs of the users of our systems. System SCHER-KHAN MAGICAR 7 is a complex electronic equipment of a car. The safety of your life, health and traffic conditions, as well as the quality of operation of nearby electronic equipment and communications, depend on its functioning and correct installation. Trust the installation of the system only
specialized service stations. During operation, periodically check the correct functioning of the system.

ATTENTION!
When purchasing, check that the warranty card is filled out correctly. The manufacturer and system supplier are not responsible for
any ignoring of the installation and operation manuals, as well as for errors made during installation. PURPOSE OF SCHER-KHAN MAGICAR 7
The SCHER-KHAN MAGICAR 7 system is a car alarm with the ability to be controlled via a radio channel using a key fob communicator with a liquid crystal display. The system exchanges information between the key fob communicator and the processor unit at a distance of up to 1,500 m. SCHER-KHAN MAGICAR 7 has a function for automatically starting the engine according to commands from: key fob, external device, internal timer, taking into account or not taking into account the temperature in the car interior and ( or) battery voltage. The car alarm is designed to work on cars with a 12 V on-board voltage and a manual or automatic transmission. The protection of the processor unit, shock sensor, call sensor and antenna unit is made according to the IP-40 standard. which involves installation inside the car. The siren is made according to the IP-65 standard and can be installed in the engine compartment, away from the exhaust manifold and high-voltage systems.

ARMING IN PIT-STOP MODE
The system allows you to turn on the security mode with the engine running without a key in the ignition switch. To implement this function it is necessary that
The appropriate connections were made during system installation and a custom programmable function value of 2-16 was selected (see
p. 83). If engine operation is monitored using a tachometer (programmable function 2-21 in value 2, see page 84), it is necessary
program the tachometer signal value (see “Programming the tachometer signal” on page 66).
To enable Pit Stop mode at the end of a ride, follow these steps:
1) Without turning off the engine, place the gear lever in neutral or “P” position
2) Apply the parking brake. Release the brake pedal
3) Press button II of the key fob for 2 seconds. You will hear one short beep from the key fob, the alarm light will flash once. After that
the ignition support will turn on, you will hear two double signals from the key fob, and the countdown to the end of the “Pit-Stop” mode will begin. The warning light will start flashing once every 5 seconds. or lights up continuously (programmable function 1-15, see page 70)
4) Turn the ignition key from the ON position to the OFF position. The engine will continue to run after this for the set time. If Programmable Function 2-16 (See page 83) is set to 2, the engine will continue to run for the amount of time set by Programmable Function 1-12 (See page 70). If Programmable Function 2-16 is set to 3 (see page 83), the motor running time is unlimited

Top Model 2007. The maximum number of service functions, powerful protection, thoughtful interface and stylish design - this model is truly a masterpiece of technical thought.

Alarm system Scher-Khan Magicar 7 equipped with a key fob communicator with feedback. It is designed to control the security system and inform the driver when the alarm is triggered, indicating its cause. That is, the car can not only be started remotely, say, to warm up the engine in winter, but also, being at a distance of up to 1,500 meters, receive a lot of useful information about the condition of the car. For example, is the trunk or hood open, are the doors locked, is the ignition turned on, is the engine running. All data is schematically displayed on the large, high-contrast liquid crystal display of the key fob. The keychain communicator is also equipped with a vibration alert, so it will definitely remind the owner of missed alarm calls. In addition, it has a high degree of protection of the radio channel from interception and code selection, and the arming and disarming channels are separated in it. This avoids the risk of intelligent hacking of the security system.

Besides, Sher-Khan Magicar 7 can turn on the engine automatically every 2, 4, 8 and 24 hours. And also by the temperature in the cabin, the voltage of the vehicle’s on-board network or by command from an external device.

Using car alarm Scher-Khan Magicar 7 You can control your car even when it is used by the owner of an additional key fob. SCHER-KHAN MAGICAR 7 is equipped with a function for synchronizing the readings of all key fobs recorded in the system memory: every action performed by additional key fobs is synchronously reflected on the main key fob.

Available in Sher-Khan Magicar 7 and a convenient “Pit-Stop” option - security mode with the engine running without a key in the ignition. With this function, the car will not cool down in the cold and will not overheat in the heat.

In addition, the system is equipped with a driver call sensor (when tapping on the windshield) and a temperature sensor. Car alarm SCHER-KHAN MAGICAR 7 adapted for Russian winters - operating temperature range from – 40 to + 85 °C.

Technical characteristics of Scher-Khan Magicar 7

Functions of the key fob communicator

• Multifunctional, 4-button;
• Displaying information on a liquid crystal display;
• Protection against interception of code messages MAGIC CODE™;
• Separate channels for arming and disarming;
• Additional confirmation code for disarming;
• Audiovisual confirmation of executed commands;
• Vibration call;
• Long-distance communication up to 1500 m with the processor unit;
• Low battery indication;
• Vehicle battery voltage indication;
• Indication of temperature in the car interior;
• Current time indication;
• Sound and visual reminder modes when receiving an alarm message;
• Economical power supply (one AAA element).

Functions of the processor unit

• Automatic engine start for cars with automatic or manual transmission:
  - by timer (every 2, 4, 8 or 24 hours);
  - by command from the key fob;
  - by command from an external device;
  - upon reaching the temperature -15, -25, +60 °C;
  - according to the discharge of the car battery below 11.5;
• Monitoring engine operation using an on-board network voltage level sensor, a generator sensor, a tachometer signal sensor;
• Ability to set the exact time to start the engine;
• Personal code for access to the car interior if the key is lost;
• Taking into account the delay in turning off the interior light (three modes);
• Protection against unauthorized recording of additional key fobs;
• Power outputs for controlling the car's central locking and trunk lock;
• Power output for alarm control (two circuits) with separate power circuit;
• Automatic arming (programmable function);
• Automatic return to security mode if the door is not opened;
• Security mode without siren signals;
• Hidden security;
• Arming/disarming without siren signals;
• Electronic current protection of all low-current outputs;
• Programming the type of blocking relay (NC or NO);
• Event programming to enable two additional channels;
• “Turbo timer” function - ignition switch-off delay from 1 to 6 minutes;
• Security with the engine running;
• Possibility of connecting negative and positive door sensors;
• Locking and unlocking doors when turning the ignition on and off;
• Programming the number of pulses for locking and unlocking the central locking system;
• Programming the central locking algorithm to control the “Comfort” function (closing the electric sunroof, electric windows);
• Alarm warning about an open door;
• PANIC or JackStop™ mode;
• HANDS-FREE function for automatic arming/disarming;
• Warning about side lights on;
• Immobilizer mode;
• Service mode “VALET”.

The Scher Khan Magicar 7 alarm system has earned numerous positive reviews from owners due to its convenience, ease of operation and additional functions. Even despite the fairly high cost of security equipment, alarms are in high demand among buyers. This article will help you quickly set up engine starting.

How to start and turn off a car using a key fob (main and additional)

To start the engine, you must press key II on the main key fob for 2 seconds. The car will turn on the security mode, the engine will start. You can check whether the car starts by simply looking at the screen of the key fob communicator. A countdown will be displayed on the screen until the engine automatically shuts down. You need to program the engine operating time in advance. Possible indicators 5 min., 15 min., 25 min. or 45 min. At the time of remote start:

• The siren will give a certain signal.
• The emergency light will turn on once.
• The LED indicator will blink once per second.
• The main key fob will emit a short signal.

It will not be possible to start the car if the parking brake is not applied. Owners of cars with a manual transmission are forced to first perform a backup procedure for starting the engine.

If, after doing the above, the engine does not start the first time, the system will try to start the engine two more times. The remote engine start did not work, which means you need to contact service.

To turn off the engine, you need to press the button on the main key fob II for 2 seconds. The shock sensor should turn on half a minute after the engine is turned off.

You managed to turn off the car using the key fob if this is indicated by:

• Siren sound twice.
• The emergency light will blink twice.
• The key fob will emit several beeps.

How to enable autostart (by temperature, time) from the key fob

To find out how to enable Sherkhan 7 autorun by time, you need to do the following:

1. Long press the two buttons II and IV. This turns on the mode for programming commands.
2. To enter timed autorun mode, you need to press and hold the IV button until the user hears the siren 13 times.
3. Next, select the autostart time: in order for the machine to start every 2 hours, press button IV, every 4 hours - button III, every 8 hours - button II, respectively.
4. Next, you will need to remove the timer from the key fob by simultaneously pressing II and IV.

However, autostart based on temperature (-15 or -25, or +60) is more popular, which is configured in the following way:

1. Connect mode 1-13, start by timer.
2. We turn on mode 1-21, which is responsible for temperature control (in buttons II, III, IV).
3. By pressing the IV button we activate autostart based on temperature. The siren will sound 21 times.
4. Then you need to select the exact engine temperature during autostart: to start the car yourself, when the engine reaches -15 degrees, press button II, we decided to set it to -25 degrees, then press key III, key IV is unlikely to be used often, since it is designed for +60 .
5. Then simultaneously press keys II and IV to remove the timer from the key fob.

The warm-up time is programmed using buttons I and II, after which you need to press button III 12 times. This increases the warm-up time.

How to disable

To disable autorun you need to reset all settings and set them to factory defaults:

• You need to turn off the alarm and turn off the ignition. The programming mode is activated as follows: buttons I and IV are pressed simultaneously for 2 seconds.
• Press the III key three times briefly. The alarm flashes will confirm the press, then three sirens can be heard and the settings will be cleared

The main reasons why autorun may not work and how to fix them

The car is not auto-started. When you press and hold button II, the door starts blinking and error 03 appears. The problem is in the door switch, urgent repairs are required.

If autostart does not work, then you need to re-program the key fob strictly according to the instructions.

Don't know which buttons to press? Does the alarm indicate an error? Can't start your car? In this case, you should contact a professional technician to set up the system or correct a poor-quality alarm installation.

MANUAL

Learn more about the reasons that prevent automatic startup
engine, see page 53.

If the startup does not happen the first time, the system will try again.
The system makes no more than three startup attempts after receiving
teams

If the car engine does not start after the last attempt,
Contact a service station to have your vehicle diagnosed.
If the starter interlock is used (programmable function 1-10
factory setting, see page 70), the engine will start
accompanied by activation of the starter interlock.

Upon successful launch:

SIREN SIGNAL:

Two signals*

EMERGENCY
SIGNALING:

Flashes twice, flashes, or stays on
(programmable function 1-15, see page 70)

LED
INDICATOR:

According to the system status. After that
When the system enters security mode it will start flashing
with a frequency of 1 time per second.

The headlights will flash five times, the smoke symbol will flash,
The countdown of the time remaining until
end of engine operation

KEY FOB SIGNAL:

Three double beeps

Enable sensors:

Once the LED starts flashing, the system will begin to monitor

condition of doors, hood, trunk, brake pedal and sensor
calling the car owner.

Shock sensor disabled in remote start mode

and will turn on only after 30 seconds. after stopping the engine.

In order to start driving your car you need
disable security, open the door, insert the ignition key into the lock

SCHER-KHAN MAGICAR 7

When calling the owner:

SIREN SIGNAL:

No signals

EMERGENCY
SIGNALING:

No signals

LED
INDICATOR:

Constant light for 3 seconds, in security mode

The call sensor symbol flashes for 10 seconds.

KEY FOB SIGNAL:

Four three-second beeps with varying
tonality. Then short signals 1 time every 6 seconds.
(reminder mode)

Note:

You can disable the owner call feature in the menu
for programming the key fob functions, see page 15.

PANIC OR JACKSTOP™ MODE [BUTTON (I)–]

When you press button I of the key fob for 2 seconds. the system will enter “Panic” mode
or JackStop™ mode - programmable function 1-10 (see page 70).
If the system has been disarmed, it will enter the security mode, locks
the doors will be locked. Siren will sound for 90 seconds, alarm
flash for 90 sec. After 90 sec. the system will go into mode
protection until it is disarmed by key fob or mode
emergency shutdown. Panic and JackStop™ modes can be stopped
by briefly pressing button I or II. Panic and JackStop™ modes
used in case of danger or when necessary to attract
attention to the car. Engine blocking relay operating mode
depends on the value of programmable function 1-10. In JackStop™ mode
programmable function 1-10 allows you to select a timer
(with a delay of 30 sec.), progressive or pseudo-random algorithm

Sher-Khan Magicar 7

Car alarm Scher-Khan 7 with feedback and auto start. It uses special principles for encoding transmitted information, protecting both from scanning and code interception. Using a key fob communicator with a liquid crystal display, you constantly receive comprehensive information about the condition of your car. Remote monitoring of information about the state of the battery and the temperature inside the car are a high indicator of convenience and comfort when using the Scher-Khan Magicar 7 system.

Features of Scher-Khan Magicar 7

• 4-button key fob communicator with LCD display
• Displaying information on the liquid crystal display
• Protection against interception of code messages MAGIC CODE™
• Separate channels for arming and disarming
• Additional disarming confirmation code
• Long-distance communication up to 1500 m with the processor unit (declared by the manufacturer)
• Remote automatic engine start with operating time indication accurate to the second
• Ability to set the exact engine start time
• Personal code for access to the car interior if the key is lost
• Event programming to enable two additional channels
• “Turbo timer” function - ignition switch-off delay from 1 to 6 minutes.
• HANDS-FREE function for automatic arming/disarming
• Immobilizer mode
• Service mode “VALET”

Scher-Khan Magicar 7 equipment

1.Operation manual	1 PC.
2. Installation Guide	1 PC.
3. Processing unit SCHER-KHAN MAGICAR 7	1 PC.
4. Keychain communicator	1 PC.
5. Additional keychain	1 PC.
6. Shock sensor with CN6 cable	1 PC.
7. Car call sensor with CN7 cable	1 PC.
8. Antenna unit	1 PC.
9. Temperature sensor	1 PC.
10. Blocking relay with block	1 PC.
11. Siren	1 PC.
12. Hood/trunk limit switch	1 PC.
13. 6-pin power connector with cable and fuse CN1	1 PC.
14. 6-pin power connector with cable and CN2 fuses	1 PC.
15. 6-pin power connector with cable and CN3 fuses	1 PC.
16. 11-pin control connector CN4	1 PC.
17. 6-wire cable connecting the antenna unit CN8	1 PC.
18. 2-wire cable for connecting additional channels CN9	1 PC.
19. Sticker for call sensor	2 pcs.
20. Sticker for antenna unit	1 PC.
21. Glass sticker	2 pcs.