How to wash the mesh. Cleaning headphones from wax and dirt. Automatic cleansing and folk remedies

The more often and better the hood works (it captures odors, combustion products, fumes and grease), the faster and more dirty its filter becomes. Over time, the grill becomes so clogged that its ventilation becomes minimal. Moreover, large deposits of fat can cause a fire.

That is why you need to wash your hood at least once every 2-4 weeks. By the way, most modern models signal the need for cleaning through special sensors on the display. For example, this could be a lit grille icon or the letter “C” (on average, it is displayed every 60 hours of engine operation, but the frequency can be adjusted independently).

Luckily, cleaning your hood isn't that difficult, especially if you have a dishwasher.

In it, a dirty filter can be washed in 1 cycle at maximum time settings and a temperature of 60 degrees.

If you don’t have a dishwasher or if it couldn’t wash the filter of old grease (this happens often), then 7 simple but super-effective tricks from our article will help you out. We will also tell you how to properly clean the kitchen hood body itself from grease, dust and soot.

Preparation

Before you start cleaning, remove the filter from under the dome. First remove/lift the front panel of the hood, then remove the filter from the guides by releasing the latch. To prevent the filter and panel from falling down, hold them with your hand.

Method 1. How to wash the filter in soap and soda solution

In fact, hood manufacturers unanimously recommend cleaning filters and front panels only with a mild soapy detergent (for example, dishwashing liquid). However, as practice shows, the “official” method does not always work, so we suggest enhancing its effectiveness with baking soda or soda ash.

Instructions:

Fill a sink or bucket with hot tap water or boiling water. The hotter the water, the more effective the cleaning.

Add baking soda (1/4 cup) and a few drops of dishwashing liquid to the water. Stir the solution with a spatula (not your hand!) to form a foam (scroll to the right to see all the steps in the photo).

Completely immerse the grease filter in the solution and leave to soak for 10 minutes.
“Scrub” the filter with a not too hard sponge/brush, then wash as usual, rinse thoroughly and dry with a towel.
Place the filter back under the hood hood.

Tip: this method almost always works, but in difficult cases, instead of soaking, you should boil the grate in the same soap-soda solution for about 5-10 minutes.

Method 2. How to clean a kitchen hood with a multi-year layer of grease with an anti-clog agent

This method is the most radical and is suitable only for the most advanced cases, when the hood has not been washed for several years.

Important! Equipment manufacturers do not recommend using this cleaning method more than 1-2 times during the entire service life, since the pipe cleaner is a caustic agent that can corrode the aluminum grate if the solution is left too long or used too often.

You will need:

For one large filter or two small ones, you will need 2-3 small packets of dry powder or about ½ cup of liquid declogging agent. Also prepare a baking sheet and boiling water. And, of course, don’t forget to wear rubber gloves and open the window!

Instructions:

Place the hood grate in a baking tray and fill it with boiling water/hot water (it should lightly cover the filter).
Sprinkle/pour the anti-clog agent evenly onto the filter. Keep it in the resulting foam for literally 5-10 minutes.

Rinse the filters several times under running water.

Method 3. How to clean the hood grille with a grease remover (for difficult cases)

Another radical method of cleaning the hood is with a grease remover or oven cleaner. For example, it could be Bugi Shumanit, Bugi Giant, Sparkling Cauldron, Oven Cleaner from Amway and others. Don't forget to open the window and use rubber gloves!

Instructions:

Treat the hood filter with the product.
Place the grille in a bag (!) to prevent the pungent odor from spreading throughout the apartment.
After 10-15 minutes, wash the mesh as usual and rinse thoroughly.

If you have children or pets, it is better to use Amway oven cleaner, as it has almost no odor and works more efficiently than its analogues. True, it is sold only through brand dealers or in the company’s online store.

Method 4. How to boil a filter in a soda solution

Stubborn, old fat deposits on the kitchen hood filter can be removed with the same soda, but by boiling.

Instructions:

Boil water in a large saucepan.
Pour baking soda into boiling water: about 1 cup in a large saucepan, 1/2 cup in a medium one.
When the soda dissolves, reduce the heat, place a filter in the solution and boil it for 10-15 minutes until the contaminants are loosened.
Wash the pan as usual.

In this video you can clearly see how to wash the hood filter from grease using this popular method.

Method 5. How to wash the hood with laundry soap

Laundry soap does an excellent job of removing grease, especially when combined with hot water.

Instructions:

Heat 2.5 liters of water in a saucepan/basin.
Grate half of the laundry soap (72%) on a medium grater and add to heated water.

When the soap has dissolved, remove the bowl from the heat, immerse the filter in it and leave to soak for 10-20 minutes.
Clean the grill as usual.

You can wipe the hood body with the same soap solution.
To increase the effectiveness of the soap solution, add a couple of tablespoons of baking soda to it.

Method 6. How to wash the hood filter with 9% vinegar

Instructions:

Soak a rag in table vinegar (9%) and generously wipe all contaminated areas with it.
Leave the filter to soak for 7-15 minutes.
Wash and rinse the mesh as usual.

Tip: before cleaning, open the window and put on rubber gloves.

Method 7. How to clean hoods with lemon

Instructions:

Peel 1-2 lemons and cut into halves.
Rub the pulp onto the surface of the grate and, if necessary, the hood body. Let the lemon juice work for about 5-10 minutes.
Wash and rinse the grate as usual.

Tip: in case of severe contamination, the grates should be soaked in a citric acid solution for several hours, or better yet, overnight. By morning your grate will be as good as new!

How to clean the hood body

So, we figured out how to wash the grease filter, how to properly wash the hood body? After all, it also becomes covered with a persistent greasy coating, dust and soot.

In fact, all manufacturers prohibit washing the case with anything other than neutral products. It is strictly forbidden to use:

Alcohol-based cleaners, and even more so solvents, as they can cause stainless steel or varnish to become dull.
Use aggressive cleaning agents (scale dissolving agents, anti-clog agents, abrasive powders and pastes, fat solvents, chlorine, acids and soda).
Use hard sponges and brushes.

Try not to delay cleaning the filters, as grease tends to harden over time, after which it becomes difficult to wash it off.
After cleaning the filters, you must reset the hood operating hours counter to zero. How to do this - read the instructions for your device.

Regardless of quality, design or cost, all headphones get dirty. With regular use, the mesh that covers the earpiece speaker suffers the most. This component gets affected by fat and earwax, and it also becomes clogged with dust. Contamination causes the sound quality to noticeably deteriorate. Next, you will learn how to properly clean your headphones.

Proper cleaning of vacuum headphones

Vacuum headphones have silicone pads that can be detached and washed with soapy water. Next, you need to clean the mesh, following the following instructions:

There are some models of headphones in which you can remove the mesh with tweezers or a small needle, picking it up on one side. But in most cases, the meshes are not removable, so you only have to clean their outer side.
It is recommended to clean with alcohol, as it not only removes dirt, but also disinfects the headphones. Pour 3-5 ml of alcohol into a small container, for example, a plastic bottle cap. Place the mesh in a container, and in the case of non-removable meshes, carefully lower the lower part of the earphone into a container with alcohol, for example, as follows:

After 2-3 minutes, all you have to do is take out the headphones and wipe off any remaining alcohol and dirt with a napkin. Please allow at least 2 hours before you use the headphones again.

Alternatively, hydrogen peroxide can be used. In this case, the lower part of the earphone must be left longer - for 15-20 minutes. Just don't immerse the earbuds completely in peroxide or alcohol, as this will damage the speakers.

The wires can also be treated with a cotton pad soaked in alcohol. A cotton pad soaked in nail polish remover will help restore the white headphone wires to their former whiteness.

Only rubberized wires should be cleaned with nail polish remover, since acetone can corrode the paint that covers the plastic headphone head.

In the following video you can clearly see how you can clean wax from headphones using peroxide:

Quick cleaning method

You can also use a quick clean. This method is suitable for headphones that cannot be disassembled. The process goes according to the following scheme:

Prepare a toothpick, a cotton swab and peroxide.
Using a stick soaked in peroxide, clean the head of each earphone from dirt.
Miniature grooves and mesh are best cleaned with a toothpick, sharpened with a match or a needle.

You can also clean the mesh using a toothbrush. In the following video, you use an old toothbrush to clean Apple's EarPods. You will also need a cotton pad and cleaning solution to wipe the entire wire:

The process will not take much of your time. All you have to do is wait until the devices are completely dry, after which you can use the headphones again.

Cleaning the headphone jack

The headphone jack on your phone or player also gets dirty. You need to clean it as follows.

A kitchen hood is an important piece of equipment that creates comfortable conditions for preparing and eating food. Untimely cleaning of the filter and grill reduces the performance of the unit, allowing the formation of soot in the kitchen. The exhaust hood, which eliminates unpleasant odors and prevents the formation of soot, must also be cleaned periodically. An increase in operating noise and a decrease in productivity are the first factors in the contamination of cleaning equipment.

How to clean the inside of a hood, if even the outside cannot be washed with a sponge and detergent? The presence of a suction effect attracts evaporation particles to the surface of the unit, thereby forming a sticky coating of fat on the device. Cleaning a kitchen hood is a rather labor-intensive process. It must be completely disassembled before washing. But the most difficult thing in the process is the direct cleaning of the mesh and filter from soot and dirt. Depending on which material

The body and parts are made, a special cleaning agent is selected. Which product needs to be used is usually indicated in the instructions for the device. Incorrectly used detergent can damage the components of the unit. Therefore, it is very important to know how to clean the hood in the kitchen correctly.

Before you begin cleansing, there are several steps you need to take:
study in detail the manufacturer’s instructions and recommendations on cleaning specific parts;
study the list of collapsible sections of the structure;
disconnect the equipment from the power supply;

dismantling and disassembly is carried out according to the description of the process in the technical documentation - this will allow you not to lose parts and put them back correctly.

If you want to know how to wash a kitchen hood, follow the following standard procedure:
Remove the top surface of the housing. Extract mesh
, closing the internal cleaning system. All details and retainer
they must be removed and soaked in a separate container with soapy water, since they will also have a greasy coating on them. filter.
Unscrew the pipe that discharges polluted air into the ventilation hatch.

After you have managed to dismantle the device and remove all the dirty parts, you can both wash the hood from grease and process all the elements, including the outer casing.

Methods for cleaning a kitchen hood

The most affordable and effective means of cleaning any kitchen hood from grease are home remedies. How can you clean the hood if it is not used very intensively and the cooking process occurs occasionally? The cleaning interval can be 6 months, using regular dishwashing detergent and a sponge. All parts and the air filter will be washed with a soapy solution. But before cleaning, you should make sure that it can be washed and not replaced.

To make the removal of dirt easier and faster, you need to clean it quarterly.

If a sticky coating with a thick layer of greasy dirt forms on the mesh, it will be necessary to use stronger agents.

Options for cleaning a kitchen hood may be as follows.

Cleaning with baking soda

Treatment with soda solution

This is the fastest, safest and cheapest way to clean the mesh. The procedure includes the following steps: Selecting a container in which you can boil the grate
in solution, depending on its dimensions. If it is large and does not fit into any pan, you can take any dish into which it will fit in width and clean it on both sides in turn.
Preparation of soda solution: 0.5 tbsp. Dilute soda in 3 liters of water.

The cleansing process takes 20-30 minutes, depending on the degree of contamination.

In a boiling soda solution, particles of any origin are separated without scratching the structure.

Treatment with ammonia If the stains are old, and when boiling in the soda solution, there are residual stains left, you can wash the hood grate with ammonia. For these purposes you will need 0.5 tbsp. alcohol diluted in 3.5 liters of hot water. Considering that ammonia has Strong smell

, it is better to carry out the procedure in a mask so as not to burn the mucous membrane, and also to open the window. The soaking process will take 1-1.5 hours, after which the mesh can be rinsed under running water and dried with a towel or napkin.

Ammonia for cleaning

Soap solution Using a soap solution requires rough cleaning of the hood from grease, since a sponge will be of little help for these purposes. Here you will need plastic or metal. To prepare the solution, you need to dissolve ordinary 72% laundry soap in hot water, with a concentration of 0.5 bars of soap per 3 liters of water. You can even boil small parts, rub the mesh with a solution and begin mechanical processing.

Acetic acid

If you don't know how to clean a greasy hood grate, try this method: treating with acetic acid is also an effective way to remove sticky dirt. The smell is pungent, so it is necessary to provide access to fresh air. Rub all the elements with a sponge soaked in vinegar. 7-10 minutes are enough to separate contaminants. After treatment with an acidic solution, the parts should be washed in running water.

Lemon acid

For mild stains, you can use lemon; as in the case of acetic acid, it can break down fat particles. Treating the hood body with lemon is very effective, as it also attracts dirt and soot forms on it. Instead of lemon juice, you can use dissolved citric acid at the rate of 2-3 tbsp. for 1 liter of water.

Chemicals

This method is used for old fatty formations when the hood has not been cleaned for a long time. For these purposes it is used drain pipe cleaner, you can try oven cleaners. If the consistency is liquid, you should soak the grate and other parts for 10 minutes and rinse with hot water. The powder should be first diluted in water and then processed.

The cleaning process will take no more time than any other processing of kitchen appliances. Regular cleaning of the filter, even in ordinary soapy water, will prevent soot from settling on the grille and other internal parts. If available, you can wash the exhaust hood elements in the dishwasher. Regular maintenance of exhaust equipment will reduce the time required to clean all parts of the structure and prolong the performance of the unit.

Cleanliness in the kitchen is very important for any housewife. We can say that the methods described in the article are suitable not only for cleaning hoods. Vinegar, citric acid and soda are used to clean a wide variety of surfaces. To keep your kitchen sparkling, check out the rules for cleansing and its cousin, . Many people do not suspect, but the dishwasher also needs regular cleaning, and ours will tell you how to do it correctly.

There are different types of headphones: in-ear, vacuum and on-ear. It is imperative to take care of these accessories - they come into direct contact with the skin. How to clean headphones from earwax and other contaminants with your own hands? I share my findings.

Types of headphones

To properly clean your headphones, you need to consider their type:

Image	Type
	Type 1. Inserts Simple design, most often non-removable. Such headphones are usually included in the basic configuration of various audio equipment.
	Type 2. Vacuum headphones Such accessories have vacuum attachments that are inserted directly into the ear canal. Typically, these headphones come with several pairs of tips of different sizes.
	Type 3. Large format A complex design that is attached with a rim to the head or neck. The earpiece completely covers the ear area.

To clean the headphones we need:

Cotton pads and buds;
Hydrogen peroxide;
Formic alcohol;
Toothpicks;
Small container for water;
Paper towels or napkins.

Depending on the design features, we will choose the method of cleaning the headphones.

Model 1. Inserts

The mesh in the in-ear headphones is covered with a plastic cover. In collapsible models, you can unscrew the lid and remove the mesh.

Pour alcohol into a small container and place the nets there for a few minutes to soak. Then take a cotton swab and wipe the surface.

If you cannot get the entire mesh, then you can clean it from sulfur and dust only from the outside. My instructions will help you achieve maximum effect:

Sulfur in headphones accumulates on the mesh, so remove large pieces first with a toothpick.

Soak a cotton pad in alcohol, wipe the housing and wires so that liquid does not get inside the bowl.
Place the inserts on paper towels and let them dry.

Model 2. Vacuum

Washing silicone ear pads is not at all difficult. Difficulties begin when you need to refresh the speaker mesh. The table describes detailed steps on how to clean the speakers of vacuum headphones in several steps:

Images	Procedure
	Step 1 Remove the silicone ear pads.
	Step 2 Rinse the pads in a weak alcohol solution and leave to dry, laying the parts on an absorbent cloth.
	Step 3 Take a small container and pour alcohol into it. Secure the headphones with the mesh side down, as shown in the photo, and leave for 5 minutes. Cleaning headphones with hydrogen peroxide is considered to be of better quality. To do this, it is enough to replace the alcohol with peroxide and increase the time spent in the liquid from 5 to 20 minutes.
	Step 4 Use a cotton pad soaked in alcohol to wipe the wires and housing. At the end of the procedure, be sure to dry the headphones with paper towels. After 2 hours, the accessory can be used again. To freshen up your white headphones, use non-acetone nail polish remover instead of alcohol.

Model 3. Overhead

Full-size models are equipped with foam rubber or other soft ear pads that are not recommended to get wet.

If the design allows, then remove these pads. Wipe the outside with a cotton pad soaked in alcohol and leave to dry

If the design does not provide for the removal of the linings– take a small container and a soft toothbrush. Wipe the inside of the ear pad with a toothbrush dipped in alcohol. Then wipe all parts of the on-ear headphones with a damp cloth and leave to dry.

Try to avoid getting moisture inside the structure to avoid damaging the electronics.

Care and storage

Use a cover, case or box for storage. During periods when you are not using the device, always put it in a special case. It will protect the wires from tangling and friction.

Choose the optimal volume level. If you constantly turn the music up to maximum, a buzzing sound will soon appear from the speaker.
Headphones under no circumstances can't get it wet. Water shorts out the electrical circuit of the headphones, and they lose their functionality.

The exception is waterproof models. You can get them wet. The packaging must have special markings.

Change foam and silicone tips periodically. Their price is more than reasonable.

Results

I told you how to clean your headphones, which I have tested myself more than once. The video in this article will show you how to bleach headphones at home and what you can do with frayed wires. If you have your own recommendations, I’ll be happy to explore them in the comments.

Cleaning the fuel pump is a fairly urgent procedure that must be carried out when the following symptoms appear:

Difficulty starting the engine with the starter;
reduction in vehicle acceleration dynamics;
jerking when pressing the gas pedal sharply;
floating speed and sluggish engine response;
the engine stalls in transition modes after pressing the accelerator, etc.

In some cases, when you press the gas, the car practically does not accelerate, overcomes inclines with great difficulty, and does not overtake. There may be several reasons for such a malfunction, but often the problem is localized in the fuel pump area. Next, we will look at issues related to what is installed in the gas tank of injection cars.

Read in this article

When and why you need to change/clean the fuel pump screen

Let's start with the fact that common problems with (the fuel pump in particular) should be roughly divided into the most common groups:

the fuel pump mesh and fuel filter are clogged;
the fuel pump itself has failed;
injector problems;

Let us add that we should also not exclude the possibility of air leaks, that is, airing of the power system. Another culprit of problems may be the pressure regulator in the fuel rail. In this case, engine malfunctions may be partially similar to some of the symptoms mentioned above. For example, a slight ingress of air into the fuel system results in the engine not starting for a long time after parking.

Let's go back to the fuel pump. Its malfunction means that the performance of the fuel supply system is reduced. If the fuel pump breaks down, then the car becomes unsuitable for normal use. Signs of a fuel pump malfunction are as follows:

It is impossible to start the engine, the fuel pump does not pump;
the engine starts, but runs with serious interruptions;

In this case, the service often recommends diagnosing, repairing or replacing the fuel pump. It should also be taken into account that the fuel pump mesh filter may become clogged inside the device. Let us immediately note that it is impossible to accurately answer the question of when to clean the fuel pump stack. Some car enthusiasts clean/replace the fuel pump mesh as needed or as a preventative measure every 50-70 thousand km. mileage, while others are faced with the need to clean the fuel pump grid for the first time at mileages of 150 thousand km or more. and more. Let us add that the operating manual for some models specifically states that it is recommended to replace the fuel pump stack once every 120 thousand km.

It should be added that the loss of dynamics and the appearance of symptoms of a clogged mesh occurs gradually. For this reason, each driver decides to clean the fuel pump himself. On powerful engines, the gradual deterioration in acceleration is not felt as much as compared to engines with a small displacement. For this reason, many owners of large-volume trucks begin to solve the problem after noticeable complications appear. Also, the condition of the pump grid is greatly influenced by the quality of the fuel being filled and a number of other factors and individual operating conditions, which we will talk about a little later.

How to clean the fuel pump yourself

Let's start with the fact that the mesh filter for the fuel pump is a coarse filter and is designed to capture large particles and deposits that are in the fuel and inevitably accumulate in the fuel. It turns out that the fuel pump has its own additional fuel filter mesh, which prevents debris from entering the fuel system from the tank parallel to the usual fuel filter. The process of cleaning or replacing the fuel pump mesh is almost similar to the general scheme for replacing the pump itself:

The fuel pump is installed directly into the gas tank. You can get to the pump from the passenger compartment, as it is located under the rear seat. To gain access to the fuel pump, you need to remove the rear seat cushion or fold down half of the sofa (if possible).
The fuel pump is usually located on the right and covered with a special plastic cover. The specified cover must be removed.
Before removing the fuel pump itself, it is necessary to relieve the fuel pressure in the system. To do this, you will need to disconnect the power connector from the fuel pump, and then turn the engine with the starter.
The next step is to remove the negative terminal from, after which the tubes from the fuel pump are disconnected. These tubes are “supply” and “return”, they are secured with clamps that need to be pressed out.
You should be prepared for the fact that a certain amount of gasoline may spill after removal. For this reason, safety precautions must be observed!
Next, you need to unscrew the special pressure ring-cover of the fuel pump. It is very difficult to unscrew this cover manually. There is a special fuel pump cover puller for removal. If there is no such puller, then you can try to carefully unscrew the ring using improvised means. We strongly recommend that you first study on specialized auto forums how to remove the fuel pump cap on a specific car model.
After unscrewing the cap, you can remove the fuel pump. Before complete removal, the remaining gasoline should be drained from its body, and the sealing ring should be removed.
Now you can begin disassembling the fuel pump housing. To clean, you will need to remove the bottom part. There is often dirt in the indicated lower part of the housing.
After this, remove the fuel pump screen. To remove the mesh, just pry out the filter at the place of attachment to the pump body using a regular screwdriver. The fuel pump strainer usually becomes completely clogged, especially on cars with high mileage.
Then the fuel pump mesh can be replaced with a new one or cleaned. It is better to wash the fuel pump mesh first with carburetor cleaner. Mechanical cleaning is done with a soft brush. Then the mesh should be dried and blown. The bottom of the pump housing and the cleaned mesh are finally washed again with gasoline.
The final step is to reassemble the fuel pump and install the device in the gas tank. To facilitate installation, it is better to invite an assistant, as it may be necessary to ensure high-quality pressure of the pump to the tank. The fact is that many gasoline pumps have a special spring, the force of which must be overcome. At the same time, you need to make sure that the rubber seal is in place and at the same time screw in the pressure ring-cover of the fuel pump. When tightening the clamping ring with a puller or improvised means, do not exceed the tightening torque. If you tighten it too tightly, the fuel pump cap may burst; if you tighten it too weakly, the fuel pump will wobble due to poor fixation.

Please note that when installing a fuel pump on many car models, you must be careful not to bend the fuel level sensor in the gas tank. It is also important to adhere to the position in which the pump was originally located.

In order to determine the correct position of the fuel pump, there are special indicators. Such indicators are made in the form of arrows and are located on the fuel pump, the gas tank body and the pressure ring. The correct installation of the fuel pump can be considered when all the arrows are in the same line. We would like to add that if the gasket is installed incorrectly, gasoline may leak out if you fill the tank full.

Now all that remains is to connect the fuel supply and return pipes to the fuel pump, while simultaneously checking that the clamps are securely fastened. The completion is to connect the electrical power connector to the fuel pump, after which you can start the car for testing.

In the case when the gas tank is heavily contaminated, cleaning or replacing the fuel pump mesh will only be a temporary measure, and the rate of subsequent contamination of the mesh will not greatly depend on the quality of the fuel being filled. In such a situation, it is necessary to remove and wash not only the mesh, but also the gas tank.

Remember, cleaning the fuel pump mesh or replacing the pump itself in the fuel tank is a responsible procedure that involves working with fuel equipment and flammable fuel. Follow safety precautions! If you have not previously removed the fuel pump yourself, do not have sufficient experience and are not confident in your abilities, then it is better to turn to specialists.

To keep the fuel pump screen clean, try not to lower the fuel level in the gas tank below ½ unless necessary. Dirt and deposits that clog the mesh are usually located at the very bottom and are the last to be drawn in by the gas pump.